
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X75-50SB is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X75-50SB is a double acting ISO 21287 compact cylinder with an adjustable extend stroke: an external stop screw trims the 75 mm stroke by up to 50 mm on site, giving a usable range of 25-75 mm. Its short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into heavy presses and gantries where a full-length body will not fit.
This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted for end-of-stroke signalling, and the B code gives a male rod thread on the 25 mm S45C hard-chrome rod. A fixed TPU bumper at each end absorbs end-of-stroke energy, the hard-anodized aluminium body resists wear, and 1/4" ports feed air at 0.15-1.0 MPa (22-145 psi) with speeds of 30-500 mm/s.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X75-50SB |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -50 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Clamp heavy pallets or castings on a machining line; the male rod thread takes a custom gripper, and the -S magnet with a DMSE switch confirms the clamped position.
Push mould gates or ladle stops in a foundry where space is tight; the compact body saves about 50% of the length of an ISO 15552 profile cylinder at the same 125 mm bore.
Remember the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock: on air loss the piston still drifts, so add a separate holding valve where a load must stay put. FA flange or LB foot mounts bolt to the ISO 21287 face, and the fitted -S magnet lets you add CMSE / DMSE switches without reordering.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
The -50 code sets a 50 mm adjustment window: an external stop screw shortens the 75 mm extend stroke by up to 50 mm, so the working range is 25-75 mm. It is double acting, runs at 30-500 mm/s on 0.15-1.0 MPa (22-145 psi) air, and the stop is an end stop only, not a load-holding brake.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, a 25 mm S45C hard-chrome plated rod with male thread (B code), and a fixed TPU bumper at each end that decelerates the piston at the ends of travel. Mounting is via FA flange, LB foot or FTC brackets with I/Y rod knuckles on the standard ISO 21287 face. This model includes the optional -S magnet, so CMSE reed or DMSE solid-state switches can be clipped to the body slots for position feedback.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.