
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X80-20B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 80mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder, the ACEJ125X80-20B pairs a 125 mm bore with an 80 mm stroke that an external stop screw can trim on site by up to 20 mm, giving a usable extend range of 60-80 mm. At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa those figures rise to 8590.3 N and 8246.7 N, with a theoretical ceiling of 1251.4 kgf at 1.0 MPa. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so heavy clamping still fits inside tight press frames and weld fixtures.
The 25 mm hard-chrome-plated S45C rod ends in a male thread (the B code), and the hard-anodized aluminium body carries 1/4" ports. A fixed TPU bumper at each end absorbs end-of-stroke energy, and speed runs 30-500 mm/s across 0.15-1.0 MPa (22-145 psi) of filtered air. Note that no magnet is fitted unless the optional -S code is ordered.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X80-20B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Clamping thick steel weldments in a fabrication cell, using the short ISO 21287 body to fit between fixture rails where an ISO 15552 profile cylinder would be about twice as long.
Swinging or lifting heavy pallet-line stop gates, where the 25 mm male-thread rod takes side loads from the gate arm and the 80 mm stroke clears a 900 mm conveyor lane.
The stop screw is a mechanical end stop for the extend stroke only - it does not lock the piston mid-stroke, so on air loss the rod will drift and a separate holding valve is needed for suspended loads.
FA flanges, LB feet and I/Y rod knuckles bolt straight to the ISO 21287 face, so standard fixtures accept it without adapter plates. If position feedback matters, order the -S variant so CMSE / DMSE switches can ride the body's magnet slots; this model without S has no magnet and no sensing.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa push is 8590.3 N and pull is 8246.7 N; the theoretical maximum is 1251.4 kgf at 1.0 MPa. The -20 code sets a 20 mm adjustment window: an external stop screw shortens the 80 mm extend stroke by up to 20 mm, so the usable range is 60-80 mm. It cannot lengthen the stroke past 80 mm, and the stop is not a mid-stroke lock - on air loss the piston still drifts.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, threaded aluminium covers, a 25 mm hard-chrome-plated S45C rod, a male rod thread (B code), 1/4" PT ports and fixed TPU bumpers at both ends. Mounting options include FA flange and LB foot plus I/Y rod knuckles. Position sensing requires the optional -S magnet: with it, CMSE / DMSE switches ride the body slots; this model without S carries no magnet, so no switch can be mounted.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.