
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X100CBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 100mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X100CBT is a double-acting JIS compact cylinder engineered for substantial actuation tasks, providing 3927 N of push force at 0.5 MPa and 5497.8 N at 0.7 MPa. Its short C-clip and riveted body architecture drastically reduces axial footprint compared to round-body alternatives, fitting high-force motion into tight machine envelopes. The unit incorporates a CB mounting bracket for secure lateral attachment.
This specific configuration features a 32 mm piston rod with a female M20x2.5 thread end and a NPT3/8 port. Deceleration relies on a fixed NBR elastomer bumper at each end rather than an adjustable cushion, meaning external shock absorbers should be added for high-energy 100 mm stroke cycles. The body includes sensor grooves, though this particular SKU ships without the internal magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X100CBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives heavy ejector pins on a 100 mm stroke to free dense plastic automotive interior panels from the mold cavity using 3927 N of push force.
Advances heavy-gauge steel blanks into a forming press, utilizing the compact C-clip body to minimize axial depth within the cramped tooling column.
Applies lateral squaring pressure to incoming wooden pallets on a conveyor, using the CB bracket to mount rigidly alongside the heavy transfer belt.
When sizing your pneumatic setup, stepping down to the 80 mm bore yields 2513.2 N push at 0.5 MPa, while stepping up to the 125 mm big-bore variant provides 6135.9 N. This 100 mm model hits a robust middle ground at 3927 N. Remember that a plain double-acting cylinder drifts when air pressure is lost or the valve is centered; the fixed NBR bumper only softens the end-of-stroke impact and will not lock the load. For fail-safe holding, an external rod lock or pilot-operated check valve is required.
To finalize your order, verify these essentials: 100 mm bore, 100 mm stroke, NPT3/8 port, female M20x2.5 rod thread, CB mounting bracket, and no sensor magnet.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3524.8 N. At 0.7 MPa, the push force reaches 5497.8 N, with a maximum push capacity of 801 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, speed is 30-500 mm/s, and temperature ranges from -20 to +70 C.
It uses a fixed NBR elastomer bumper at each end to absorb shocks, which is not field-adjustable like an air cushion; high-speed applications may need external shock absorbers. Additionally, it does not hold position on air loss—the piston drifts, so a fail-safe load requires an external rod lock or pilot-operated check valve.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.