
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X10BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 10mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X10BT is a double-acting JIS compact cylinder engineered for heavy-duty operations within a minimal axial footprint. Utilizing a short C-clip and riveted piston-to-rod body design, it conserves machine mounting depth where conventional round-body units cannot fit. This 100 mm bore configuration generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa, extending to 5497.8 N push at 0.7 MPa.
This specific model includes a male-thread piston rod end (M26x1.5) for direct, secure coupling to tooling, alongside a NPT3/8 port. Deceleration is managed by a fixed NBR elastomer bumper at each end rather than an adjustable air cushion, meaning external shock absorbers should be specified for high-energy impacts. The body retains standard magnetic-switch grooves, though this unit ships without a sensor magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X10BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides high 3927 N thrust for securing heavy injection mold halves within tight press cavities, leveraging the short 10 mm stroke for rapid cycling.
Drives short-stroke stamping and heavy blanking operations in automotive lines, where the male M26x1.5 thread securely attaches to high-impact tooling.
Applies lateral squaring force to heavy pallets or unit loads on packaging conveyors, fitting into shallow machine frames due to its compact C-clip body.
Selecting this 100 mm bore with a 10 mm short stroke provides immense thrust in a very compact package. If you need slightly less force, stepping down to the 80 mm bore yields 2513.2 N push at 0.5 MPa; conversely, moving up to the 125 mm big-bore variant provides 6135.9 N push. Keep in mind that a plain ACQ body does not hold its load if air pressure drops or the valve is centered—the rod will drift, and the fixed bumper only decelerates near the stroke end, so an external rod lock or pilot-operated check valve is required for fail-safe holding.
When requesting a quote, verify your ordering essentials: 100 mm bore, 10 mm stroke, NPT3/8 port, male M26x1.5 rod thread (B), and no magnet. The standard stroke ceiling for this bore is 100 mm, with long-stroke variants available up to 300 mm.
Quick checklist
This 100 mm bore double-acting cylinder delivers 3927 N push and 3524.8 N pull at 0.5 MPa, and 5497.8 N push at 0.7 MPa. The maximum push force is 801 kgf at 1.0 MPa. It operates on filtered air at 0.15-1.0 MPa, with a speed range of 30-500 mm/s.
No, it uses a fixed NBR elastomer bumper at each end to absorb the end stop, which is not field-adjustable like an air cushion. For high-speed or high-energy loads, you should add an external shock absorber or slow the approach. Additionally, the body has sensor grooves but this model ships without a sensor magnet.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.