
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X15ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 15mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X15ST is a double-acting JIS compact cylinder engineered for substantial thrust within a minimal axial footprint. Utilizing a C-clip and riveted piston-to-rod assembly, the short body design conserves mounting depth where a conventional round-body unit would be too bulky. This 100mm bore configuration generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa.
Equipped with an integrated piston magnet (the -S option), the body features peripheral grooves ready to accept AirTAC reed or electronic switches for position sensing. Deceleration at stroke ends relies on a fixed NBR elastomer bumper rather than an adjustable air cushion, meaning high-energy cycles may require external shock absorption. The 32mm diameter piston rod terminates in a female M20x2.5 thread for secure load coupling. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X15ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 3927 N of extend force at 0.5 MPa to secure large injection mold halves or heavy platens during material injection cycles.
Drives short 15mm stamping or marking actions on thick metal sheets where high impact force is needed in a compact axial space.
Actuates heavy-duty pallet flap folders or large case sealers, using the magnetic sensor to confirm full 15mm travel before the conveyor advances.
When sizing your drive, consider the neighbouring bores: stepping down to the 80mm bore yields 2513.2 N of push at 0.5 MPa, while stepping up to the 125mm big-bore variant provides 6135.9 N. Remember that a standard ACQ body does not hold its position if air pressure drops or the valve is centred; the piston will drift, and the fixed bumper only decelerates it near the end of travel. For fail-safe load holding, an external rod lock or pilot-operated check valve is required. To order this specific unit, confirm the 100mm bore, 15mm stroke, NPT3/8 port, integrated magnet, and female M20x2.5 rod thread.
Quick checklist
This 100mm bore double-acting cylinder provides 3927 N push and 3524.8 N pull at 0.5 MPa, 5497.8 N push at 0.7 MPa, and a maximum push force of 801 kgf at 1.0 MPa. It operates at speeds of 30-500 mm/s within a pressure range of 0.15-1.0 MPa.
It uses a fixed NBR elastomer bumper at each end to absorb end-stop impact, which is not a field-adjustable air cushion. Additionally, it does not feature a locking mechanism; if air is lost, the rod drifts, so an external rod lock is needed for fail-safe holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.