
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X20ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 20mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X20ST is a double-acting, single-rod JIS compact cylinder engineered to deliver substantial force in a minimal axial footprint. Utilizing a riveted piston-to-rod connection and C-clip assembly, the short body design significantly reduces mounting depth compared to conventional round-body units. At 100 mm bore, it generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa.
This specific configuration includes a 20 mm stroke and a built-in piston magnet (-S) for position detection. The bore interior is hard-anodized for longevity, and the piston relies on a two-way seal. End-of-stroke energy is managed by fixed NBR elastomer bumpers rather than adjustable air cushions. The body features full-length magnetic-switch grooves that accept either reed or electronic solid-state sensors. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X20ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 20 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides high-force knockout strokes for ejecting dense plastic or aluminum cast parts from injection molds where short retraction depth is required.
Executes short 20 mm pressing operations for forming thick sheet metal brackets, leveraging 5497.8 N of thrust at 0.7 MPa.
Acts as a robust mechanical stop or positioning pin in automated pallet handling lines, absorbing heavy lateral inertia via the NBR bumper.
Selecting this 100 mm bore model provides a maximum push of 801 kgf at 1.0 MPa. If your application requires less force, stepping down to the 80 mm bore yields 2513.2 N push at 0.5 MPa. If you need greater thrust, this is the largest standard bore in the main range before moving into the 125 mm big-bore variant, which outputs 6135.9 N at 0.5 MPa. Keep in mind that a plain compact cylinder like this will drift and cannot hold a load if air pressure is lost or the valve is centered; an external rod lock or pilot-operated check valve is required for fail-safe positioning.
When ordering, verify your essential parameters: 100 mm bore, 20 mm stroke, NPT3/8 port, the integrated magnet for sensing, and the default female rod-end thread (M20x2.5). The 32 mm diameter piston rod couples directly to the load, but side loading must be strictly avoided on this short compact body.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3524.8 N. At 0.7 MPa, the push force is 5497.8 N. The maximum push force is 801 kgf at 1.0 MPa. Operating pressure ranges from 0.15-1.0 MPa, with a speed range of 30-500 mm/s.
No, it uses fixed NBR elastomer bumpers at both ends to absorb end-stop impact, which are not field-adjustable; for high kinetic energy loads, add an external shock absorber. The -S code indicates a built-in piston magnet for use with AirTAC reed or electronic switches.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.