
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X35T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 35mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X35T is a double-acting, single-rod JIS compact cylinder engineered to deliver substantial force in a minimal axial footprint. Utilizing a C-clip and riveted piston-to-rod assembly rather than a traditional tie-rod framework, the body length is drastically reduced to save machine mounting depth. This specific 100 mm bore configuration generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa, making it well-suited for heavy-duty positioning tasks.
Built for demanding environments, the hard-anodized inner bore pairs with a fixed NBR elastomer bumper at each end to absorb end-stop impact. It is important to note this is a fixed bumper, not an adjustable air cushion; operators running at high speeds should add an external shock absorber or decelerate the approach. This unit ships without a sensor magnet but retains magnetic-switch grooves around the body, and uses a 32 mm rod with a standard female M20x2.5 thread end. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X35T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides the heavy push force needed to reposition injection molding platens or heavy tooling carts within a confined machine envelope.
Drives heavy-duty knockout pins or lower ejection rams in mechanical stamping presses, utilizing its 35 mm stroke for rapid part release.
Actuates vertical lift platforms in end-of-line palletizing cells, where the fixed NBR bumper reliably absorbs the high deceleration energy.
When sizing your actuator, stepping down to the 80 mm bore yields 2513.2 N of push at 0.5 MPa, while this 100 mm bore provides 3927 N. If your application requires even more power, the 125 mm variant offers 6135.9 N. Keep in mind that a standard ACQ body does not hold its position or load if air pressure is lost or the valve is centered; the rod will drift, and the fixed bumper only decelerates it near the stroke end. For fail-safe load holding, an external rod lock or pilot-operated check valve is required. To order this model, confirm the 100 mm bore, 35 mm stroke, NPT3/8 port, default female rod thread, and no magnet.
Quick checklist
This 100 mm bore cylinder generates 3927 N push and 3524.8 N pull at 0.5 MPa, and 5497.8 N push at 0.7 MPa, with a maximum push capacity of 801 kgf at 1.0 MPa. It operates between 0.15-1.0 MPa at speeds of 30-500 mm/s.
No, the ACQ100X35T uses a fixed NBR elastomer bumper at each end to absorb impact. It is not a field-adjustable air cushion, so for high-energy or high-speed cycles, you should add an external shock absorber or slow the approach.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.