
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X40SBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 40mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X40SBT is a double-acting JIS compact cylinder engineered to deliver substantial thrust within a minimal axial footprint. By utilizing a C-clip and riveted piston-to-rod assembly rather than a traditional long body, it achieves a very short overall length, saving valuable mounting depth in large machinery. At 100 mm bore, it generates 3927 N of push force at 0.5 MPa and reaches a maximum push capacity of 801 kgf at 1.0 MPa.
This specific configuration includes a built-in piston magnet (-S) for position sensing and a male M26x1.5 threaded rod end (-B) for direct load coupling. The 32 mm piston rod is supported by a hard-anodized bore, while deceleration is handled by fixed NBR elastomer bumpers at each end. Because these bumpers are not adjustable, high-energy cycles may require an external shock absorber to prevent mechanical damage. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X40SBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Applies 5497.8 N of thrust at 0.7 MPa to seat heavy metal inserts into injection mold tooling, using the male M26x1.5 thread for a rigid mold interface.
Locks large machining center pallets in place during heavy milling, relying on the compact body to minimize interference with the moving work envelope.
Drives a heavy-gauge sheet metal feed straightener upward into position, taking advantage of the 801 kgf maximum push rating to lift substantial dead weight.
When sizing your actuator, compare this 100 mm bore (3927 N push @0.5 MPa) against the adjacent sizes: stepping down to an 80 mm bore yields 2513.2 N push, while stepping up to a 125 mm bore provides 6135.9 N push. Ensure your setup can handle the 32 mm rod and NPT3/8 air supply. To order this exact unit, confirm the 40 mm stroke, the male M26x1.5 thread, and the integrated magnet for reed or electronic switches. Note that a standard ACQ body does not hold its load if air pressure drops or the valve is centered; the rod will drift. For fail-safe positioning, an external rod lock or pilot-operated check valve is required.
Quick checklist
This 100 mm bore cylinder provides 3927 N push and 3524.8 N pull at 0.5 MPa, 5497.8 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It features a 32 mm rod, a NPT3/8 port, and a male M26x1.5 rod end thread.
No, it uses fixed NBR elastomer bumpers at the stroke ends to absorb impact. These are not adjustable, so for high-speed or high-energy loads, you should add an external shock absorber or reduce the approach speed.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.