
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X45ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 45mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X45ST is a double-acting, single-rod JIS compact cylinder engineered for substantial actuation tasks, yielding 3927 N of push force and 3524.8 N of pull force at 0.5 MPa. Its short C-clip and riveted body architecture significantly curtails axial mounting depth compared to conventional round-body units, conserving valuable machine footprint in tight assemblies.
This 100mm bore unit integrates a built-in piston magnet for position sensing via AirTAC reed or electronic solid-state switches seated in the body grooves. End-of-travel energy is managed by fixed NBR elastomer bumpers rather than adjustable air cushions, meaning high-speed operations may require external shock absorption. The 32mm piston rod terminates in a female M20x2.5 thread, and pneumatic supply connects via a NPT3/8 port. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X45ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Supplies the robust 3927 N push force required to eject dense plastic components from heavy injection molding tools, utilizing the 45mm stroke for rapid retraction.
Acts as a compact actuator on multi-station automated presses, delivering substantial clamping pressure within a short axial frame where traditional cylinders cannot fit.
Operates heavy diverter gates on high-throughput packaging lines, using the integrated magnet to confirm gate open/close status to the PLC.
When sizing your drive, consider stepping down to the 80mm bore (2513.2 N push at 0.5 MPa) for lighter loads, or up to the 125mm big-bore variant (6135.9 N push at 0.5 MPa) if your thrust requirements exceed this model. Remember that a standard ACQ body will drift and cannot maintain a load position if air pressure drops or the directional valve centers; a fail-safe setup demands an external rod lock or pilot-operated check valve. To finalize this configuration, confirm the 100mm bore, 45mm stroke, NPT3/8 porting, the required female M20x2.5 rod thread, and the -S magnet option for sensing.
Quick checklist
This 100mm bore cylinder provides 3927 N push and 3524.8 N pull at 0.5 MPa, 5497.8 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It operates at 30-500 mm/s, accepts a NPT3/8 port, and uses a 32mm rod with an M20x2.5 female thread.
It uses fixed NBR elastomer bumpers at both ends to absorb end stops, which are not adjustable like an air cushion; high energy cycles may need external shock absorbers. Furthermore, it does not hold its load if air is lost, so an external rod lock or pilot-operated check valve is required for fail-safe positioning.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.