
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X50T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 50mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X50T is a double-acting JIS compact cylinder engineered to deliver substantial thrust within a minimal axial footprint. Utilizing a riveted piston-to-rod assembly and C-clip closure, this thin-body design significantly reduces overall mounting depth compared to round-body alternatives. At 100 mm bore, it generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa, peaking at a maximum push capacity of 801 kgf at 1.0 MPa.
This specific configuration features a 32 mm piston rod with a default female M20x2.5 thread end and a NPT3/8 air supply port. Deceleration at stroke extremes is handled by fixed NBR elastomer bumpers rather than adjustable pneumatic cushions; operators should slow the approach or utilize external shock absorbers for high-energy loads. While the body includes magnetic-switch grooves, this variant ships without the internal magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X50T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides the 5497.8 N extension force at 0.7 MPa needed to drive a small stamping die or hold a heavy metal blank firmly in a press bed.
Uses its 50 mm stroke and 801 kgf maximum push capacity to square up loaded wooden pallets before stretch wrapping, ensuring stable load geometry.
Acts as a compact knockout pin driver inside tight machinery frames, leveraging the short C-clip body depth to fit where standard round cylinders cannot.
When sizing your actuator, stepping down to an 80 mm bore yields 2513.2 N of push at 0.5 MPa, whereas stepping up to the largest standard size, 125 mm, provides 6135.9 N. The 100 mm bore hits a strong middle ground for heavy-duty pressing and high-tonnage clamping. Remember that a plain ACQ cylinder will not hold its position if air pressure drops or the directional valve centers; the rod drifts, and the fixed NBR bumper only decelerates the end stop. For fail-safe load holding, an external rod lock or pilot-operated check valve is required. To order this exact unit, confirm the 100 mm bore, 50 mm stroke, NPT3/8 port, female rod thread, and no magnet.
Quick checklist
The 100 mm bore generates 3927 N push and 3524.8 N pull at 0.5 MPa, 5497.8 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. It uses a 32 mm rod, a NPT3/8 port, a female M20x2.5 rod-end thread, and operates at speeds of 30-500 mm/s.
No, the ACQ100X50T uses fixed NBR elastomer bumpers at each end to absorb end-stop impact. It is not an adjustable pneumatic cushion. For high-speed or high-mass loads, you should slow the approach or add an external shock absorber.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.