
The AirTAC ACQ Ultra Thin Air Cylinder ACQ100X5ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø100mm bore and 5mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ100X5ST is a double-acting JIS compact cylinder engineered for high-force applications within a minimal axial footprint. Utilizing a C-clip and riveted piston-to-rod assembly, the short body design significantly reduces mounting depth compared to standard round-body actuators. At 100 mm bore, it generates 3927 N of push force and 3524.8 N of pull force at 0.5 MPa, scaling up to 5497.8 N push at 0.7 MPa.
This specific configuration includes an integrated -S piston magnet for position sensing via AirTAC reed or electronic switches fitted into the body grooves. Deceleration at the 5 mm stroke endpoints relies on a fixed NBR elastomer bumper rather than an adjustable air cushion. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ100X5ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø100 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M20×2.5 female / M26×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 3927 N of compact force to eject dense plastic components from injection molding tools where axial depth is strictly limited.
Delivers massive 5497.8 N push force at 0.7 MPa to seat large bearings or bushings into housings over a short 5 mm travel.
Drives hardened steel stamps into heavy gauge metal plates, utilizing the 801 kgf maximum push capacity for deep part identification.
When sizing this 100 mm bore actuator, evaluate the neighboring standard bores to match your force requirements precisely. Stepping down to an 80 mm bore yields 2513.2 N push at 0.5 MPa, while stepping up to a 125 mm big-bore variant provides 6135.9 N push at 0.5 MPa. The ACQ100X5ST is optimal when you need massive force within an extremely short 5 mm travel distance.
Remember that a standard double-acting compact cylinder does not hold its position or load if air pressure drops or the directional valve is centered; the rod will drift. For fail-safe load holding, an external rod lock or pilot-operated check valve is required. To order, confirm the 100 mm bore, 5 mm stroke, NPT3/8 port, female M20x2.5 rod thread, and the -S magnet option.
Quick checklist
The 100 mm bore generates 3927 N push and 3524.8 N pull at 0.5 MPa, 5497.8 N push at 0.7 MPa, and a maximum push of 801 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and speed ranges from 30-500 mm/s.
It uses a fixed NBR elastomer bumper at each end to absorb impact, which is not a field-adjustable air cushion; for high-energy cycles, you should slow the approach or add external shock absorption. The included -S magnet allows tracking by AirTAC reed or electronic switches mounted in the body slots.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.