
The AirTAC ACQ Ultra Thin Air Cylinder ACQ32X100SBFAT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø32mm bore and 100mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ32X100SBFAT is a double-acting JIS compact cylinder engineered around a short C-clip and riveted body, which drastically cuts axial mounting depth compared to round-body units. At 32mm bore, it generates 402.1N of push force and 301.6N of pull force at 0.5 MPa, operating via a NPT1/8 port.
This specific configuration includes an S magnet for slot-mounted AirTAC reed or electronic switches, a B male M14x1.5 piston rod end for direct load coupling, and an FA mounting bracket. It relies on a fixed NBR elastomer bumper at each end to absorb end-stop impact rather than an adjustable air cushion. Operating at 30-500 mm/s, this 100mm stroke represents the maximum standard length for this bore before moving into the long-stroke range. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ32X100SBFAT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Actuates a routing flap on a logistics conveyor belt to sort parcels, utilizing the full 100mm stroke to clear the transport lane.
Pushes raw bar material into the spindle collet, where the male M14x1.5 rod thread secures the pushing attachment directly to the load.
Folds the major side flaps of corrugated shipping cartons, using the 402.1N extend force to overcome board stiffness.
When sizing this 32mm bore, stepping down to a 25mm bore yields 245.4N of push at 0.5 MPa, while stepping up to a 40mm bore provides 628.3N. To finalize your order, confirm the 32mm bore, 100mm stroke, NPT1/8 port, S magnet, B male M14x1.5 rod thread, and FA bracket. Remember that a plain ACQ cylinder does not hold its load if air pressure drops or the valve is centered; the piston drifts and the fixed bumper only decelerates near the stroke end. For a fail-safe hold, an external rod lock or pilot-operated check valve is required.
Quick checklist
This 32mm bore double-acting cylinder provides 402.1N push and 301.6N pull at 0.5 MPa, 562.9N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa with a proof pressure of 1.5 MPa.
No. The ACQ32 uses a fixed NBR elastomer bumper at each end to absorb impact, not an adjustable air cushion. Additionally, it does not hold a load if air is lost or the valve is centered; you must add an external rod lock or pilot-operated check valve for fail-safe position holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.