
The AirTAC ACQ Ultra Thin Air Cylinder ACQ32X30BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø32mm bore and 30mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ32X30BT is a double-acting JIS compact cylinder engineered with a 32 mm bore and 30 mm stroke. It utilizes a C-clip and riveted piston-to-rod assembly to minimize overall axial length, saving valuable mounting depth where a conventional round-body unit would not fit. Delivering 402.1 N of push force at 0.5 MPa, it is built around a hard-anodized aluminum barrel.
This specific configuration includes a male M14x1.5 piston rod thread for direct, secure coupling to your load. The unit relies on a fixed NBR elastomer bumper at each end of travel to absorb impact rather than an adjustable air cushion. While it lacks a built-in magnet, the body retains peripheral grooves for standard AirTAC switch mounting if a magnet is added later. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ32X30BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø32 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Indexes small tooling blocks with precise 30 mm strokes, leveraging the 402.1 N push force to overcome spring-loaded detents.
Drives the rotary-to-linear motion for film cutting crimpers, where the short C-clip body prevents interference with guide rails.
Actuates secondary ejection plates for delicate plastic parts, using the male M14x1.5 thread for rigid mechanical attachment.
When sizing this 32 mm bore model, consider stepping down to a 25 mm bore for lighter duties (245.4 N push at 0.5 MPa) or up to a 40 mm bore for heavier tasks (628.3 N push at 0.5 MPa). Remember that a standard ACQ body will not hold a load if air pressure drops or the valve is centered; the piston drifts and the fixed bumper only decelerates near the end of stroke. For fail-safe positioning, specify an external rod lock or pilot-operated check valve.
To order this exact unit, confirm the 32 mm bore, 30 mm stroke, NPT1/8 port, and the male-thread rod end (B option). It operates at pressures from 0.15 to 1.0 MPa with a speed range of 30-500 mm/s.
Quick checklist
At 0.5 MPa, the push force is 402.1 N and the pull force is 301.6 N. At 0.7 MPa, the push force is 562.9 N. The maximum push force is 82 kgf at 1.0 MPa. The maximum standard stroke available for this 32 mm bore is 100 mm.
No, this model uses a fixed NBR elastomer bumper at each end, not a field-adjustable air cushion. For high-speed or high-energy impacts, slow the approach or add an external shock absorber. Additionally, the cylinder does not hold position on air loss; the rod drifts, so an external rod lock is required for fail-safe load holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.