
The AirTAC ACQ Ultra Thin Air Cylinder ACQ32X5ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø32mm bore and 5mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ32X5ST is a double-acting JIS compact cylinder engineered for extremely short linear movements. It yields 402.1 N of push force and 301.6 N of pull force at 0.5 MPa, making it suitable for high-force clamping in confined spaces. The C-clip and riveted piston assembly radically reduces overall axial length compared to round-body alternatives, minimizing machine footprint.
Fitted with an internal piston magnet, the body accepts AirTAC reed or electronic solid-state switches via peripheral slots for precise end-of-stroke detection. The 32 mm bore uses a NPT1/8 port and a 16 mm piston rod with a female M8x1.25 end thread. Deceleration is handled by fixed NBR elastomer bumpers at both ends rather than adjustable air cushions, so external shock absorbers should be considered for high-energy impacts. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ32X5ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø32 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Applies 402.1 N of rapid holding force to secure a printed circuit board drill cartridge over a 5 mm travel before the spindle begins its high-speed cycle.
Delivers a short 5 mm pressing action to hold corrugated packaging flaps aligned while hot-melt adhesive cures on an automated boxing line.
Uses the 32 mm bore's 301.6 N pull force to retract a small pilot pin from a progressive die immediately after the press stroke completes.
For sizing context, stepping down to a 25 mm bore reduces the 0.5 MPa push force to 245.4 N, while stepping up to a 40 mm bore increases it to 628.3 N. This 32 mm bore with a 5 mm stroke is optimal when you need substantial pressing power over a microscopic travel distance. When ordering, confirm the 32 mm bore, 5 mm stroke, NPT1/8 port, female M8x1.25 rod thread, and the required magnetic sensor option.
Note that a standard double-acting cylinder cannot hold its position if air pressure drops or the directional valve is centered. The rod will drift, and the fixed NBR bumper only decelerates the piston near the stroke end without locking it. If your application requires fail-safe load holding, you must integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
The 32 mm bore generates 402.1 N push and 301.6 N pull at 0.5 MPa, 562.9 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. The operational speed range is 30-500 mm/s.
It uses fixed NBR elastomer bumpers at each end to absorb shock, which are not adjustable like an air cushion; for high-speed impacts, slow the approach or add external shock absorbers. The built-in magnet works with AirTAC reed or electronic switches mounted in the body slots.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.