
The AirTAC ACQ Ultra Thin Air Cylinder ACQ40X25LBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø40mm bore and 25mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ40X25LBT is a double-acting JIS compact cylinder engineered to deliver 628.3 N of push force and 527.8 N of pull force at 0.5 MPa. Its short C-clip and riveted piston-to-rod assembly drastically reduce axial length compared to traditional round-body units, saving valuable machine footprint in tight assemblies. This LB-bracket mounted model uses a 16 mm piston rod and an M8x1.25 female rod-end thread for straightforward load coupling.
This specific configuration moves a 25 mm stroke within a 40 mm bore that supports standard travels up to 100 mm. Instead of an adjustable air cushion, the end caps house fixed NBR elastomer bumpers to absorb end-stop energy. The body retains magnetic-switch grooves around its circumference, though this particular SKU ships without the internal magnet. Operating pressure ranges from 0.15 to 1.0 MPa, with a standard speed range of 30-500 mm/s. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ40X25LBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø40 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Feeds a circular saw blade at a controlled 25 mm stroke to singulate printed circuit boards, utilizing the 628.3 N push force to maintain steady cutting pressure.
Actuates a mechanical arm to tuck minor flaps on packaging lines, where the LB bracket provides a rigid pivot point for the 527.8 N retract motion.
Drives a short pin into aluminum extrusions for locating holes, relying on the fixed NBR bumper to soften the impact at the end of each cycle.
When sizing this 40 mm bore, you can step down to an ACQ32X25LB offering 402.1 N push at 0.5 MPa for lighter loads, or step up to an ACQ50X25LB providing 981.8 N push if your application demands greater thrust. To finalize your order, confirm the 40 mm bore, 25 mm stroke, NPT1/8 port, female M8x1.25 rod thread, and the LB mounting bracket. Note that a plain ACQ body does not hold its position if air pressure drops or the valve is centered; the rod will drift, and the fixed bumper only decelerates it near the stroke end. For fail-safe load holding, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
This 40 mm bore cylinder generates 628.3 N push and 527.8 N pull at 0.5 MPa, and 879.6 N push at 0.7 MPa. The maximum push force is 128 kgf at 1.0 MPa. It operates between 0.15 and 1.0 MPa, with a proof pressure of 1.5 MPa, and travels at speeds of 30-500 mm/s.
No. It uses fixed NBR elastomer bumpers at both ends rather than a field-adjustable air cushion, so you should slow the approach or add external shock absorbers for high-energy loads. Additionally, while the body features sensor grooves, this specific model ships without the internal magnet required for reed or electronic switches.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.