
The AirTAC ACQ Ultra Thin Air Cylinder ACQ40X25ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø40mm bore and 25mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ40X25ST is a double-acting JIS compact cylinder engineered for space-constrained pneumatic setups, yielding 628.3 N of push force and 527.8 N of pull force at 0.5 MPa. Its C-clip and riveted piston-to-rod assembly drastically reduces axial depth compared to traditional round-body units. The 40 mm bore features a hard-anodized inner wall and a 16 mm piston rod.
Equipped with an S-option piston magnet, this model accepts AirTAC reed or electronic switches along the full-body sensor grooves for precise end-position detection. Deceleration is handled by fixed NBR elastomer bumpers at both ends rather than adjustable air cushions, so high-speed operations may require external shock absorbers. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ40X25ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø40 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 628.3 N of extend force to secure aluminum housings inside CNC machining centers, utilizing the short 25 mm stroke to minimize fixture protrusion.
Drives folding mechanisms on corrugated packaging lines where the compact body depth prevents interference with passing conveyor traffic.
Pushes bearings or bushings into cast housings on automated assembly presses, relying on the built-in magnet to trigger solid-state insertion confirmation switches.
Selecting this 40 mm bore involves balancing force and spatial limits; it provides 628.3 N push at 0.5 MPa, sitting neatly between the 32 mm bore (402.1 N push) and the 50 mm bore (981.8 N push). If your application demands a fail-safe hold upon air loss, note that a standard ACQ body will drift and the fixed bumper only decelerates near stroke end, meaning an external rod lock or pilot-operated check valve is required for secure load holding.
When requesting a quote, verify the 25 mm stroke, NPT1/8 port size, and the built-in magnet for switch mounting. The default female M8x1.25 rod thread couples directly to your load, though side loading must be minimized on this short compact rod to prevent premature seal wear.
Quick checklist
At 0.5 MPa, this double-acting 40 mm bore cylinder generates 628.3 N of push force and 527.8 N of pull force. At 0.7 MPa, the push force increases to 879.6 N, with a maximum push capacity of 128 kgf at 1.0 MPa. It operates within a pressure range of 0.15-1.0 MPa and travels at speeds between 30-500 mm/s.
It uses fixed NBR elastomer bumpers at both ends to absorb end stops, which are not field-adjustable; for high kinetic energy loads, slow the approach or add external shock absorbers. The S-option includes a built-in piston magnet that works with AirTAC reed or electronic switches fitted into the body grooves.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.