
The AirTAC ACQ Ultra Thin Air Cylinder ACQ40X40T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø40mm bore and 40mm stroke, PT1/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ40X40T is a double-acting, single-rod JIS compact cylinder engineered to deliver 628.3 N of push force and 527.8 N of pull force at 0.5 MPa. Its space-saving C-clip and riveted piston-to-rod architecture drastically reduce axial mounting depth compared to conventional round-body units, making it highly effective for tight machine envelopes.
This 40 mm bore unit features a 16 mm piston rod, a NPT1/8 port, and a default female M8x1.25 rod-end thread. End-of-stroke deceleration is handled by fixed NBR elastomer bumpers rather than adjustable air cushions, meaning high-energy cycles may require external shock absorption. The body includes magnetic-switch grooves, though this specific SKU ships without the internal magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ40X40T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Actuates routing gates on packaging conveyors where the short 40 mm stroke and 628.3 N extend force reliably push cartons onto secondary lines without occupying excessive frame depth.
Secures workholding fixtures inside machining centers, utilizing the 16 mm rod and female M8x1.25 thread to drive clamping arms against parts under 0.5 MPa operating pressure.
Pushes assembled printed circuit boards out of test fixtures, taking advantage of the hard-anodized aluminum bore to ensure smooth, low-friction ejection at cycling speeds up to 500 mm/s.
When sizing this 40 mm bore model, consider stepping down to the 32 mm bore for lighter loads, which provides 402.1 N of push force at 0.5 MPa. If your application demands more power, stepping up to the 50 mm bore yields 981.8 N of push force at the same pressure. This ACQ40X40T configuration features a 40 mm stroke, a NPT1/8 port, a female M8x1.25 rod thread, and no sensor magnet.
Keep in mind that a standard double-acting cylinder of this type will not hold a load if air pressure is lost or the directional valve is centered, as the piston will drift and the NBR bumper only decelerates the stroke near its end points. For fail-safe vertical load holding, you must integrate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628.3 N of push force and 527.8 N of pull force. At 0.7 MPa, the push force increases to 879.6 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa, and the speed range is 30-500 mm/s.
No, it uses fixed NBR elastomer bumpers at both ends to absorb end-stop impact, which are not field-adjustable, so high-speed applications may need external shock absorbers. Additionally, while the body has sensor grooves, this specific model ships without the internal magnet required for AirTAC reed or electronic switches.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.