
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X25T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 25mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X25T is a double-acting JIS compact cylinder engineered for substantial thrust within a minimal axial envelope. It produces 1558.6 N of push force and 1401.5 N of pull force at 0.5 MPa, utilizing a 20 mm piston rod and a NPT1/4 port.
This thin body relies on a C-clip and riveted piston-to-rod joint to minimize mounting depth. Deceleration is handled by fixed NBR elastomer bumpers at each end stop rather than adjustable air cushions, meaning high-speed cycles may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X25T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives the sealing head on case erectors where a 25 mm stroke applies precise pressure to fold and tape flaps.
Locks aluminum workholding fixtures onto machining centers, utilizing 1558.6 N of extend force to resist cutting vibration.
Pushes finished plastic parts out of small injection molds, fitting neatly into tight mold base cavities.
Stepping down, the 50 mm bore yields 981.8 N push at 0.5 MPa, while stepping up to the 80 mm bore provides 2513.2 N. Remember that this standard double-acting design drifts if air pressure drops or the valve centers; the fixed NBR bumper decelerates the stroke end but does not lock the load, so a pilot-operated check valve is needed for fail-safe holding. To order, confirm the 63 mm bore, 25 mm stroke, NPT1/4 port, female M10x1.5 rod thread, and no sensor magnet.
Quick checklist
At 0.5 MPa, the push force is 1558.6 N and the pull force is 1401.5 N. At 0.7 MPa, the push force is 2182 N. The maximum push force is 318 kgf at 1.0 MPa.
No, the end stops use fixed NBR elastomer bumpers, not adjustable air cushions, so you must slow the approach or add external shock absorbers for high energy. This specific unit lacks the internal magnet, so while the body has sensor grooves, you cannot use reed or electronic switches without a magnet-equipped variant.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.