
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X35SBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 35mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X35SBT is a double-acting JIS compact air cylinder engineered with a short C-clip and riveted body structure, significantly reducing axial mounting depth where a conventional round-body unit would not fit. It yields 1558.6 N of push force and 1401.5 N of pull force at 0.5 MPa, scaling up to 2182 N extend force at 0.7 MPa.
This specific configuration includes a built-in piston magnet (-S) for position sensing via AirTAC reed or electronic switches fitted into the body grooves. The -B code indicates a male M18x1.5 piston rod end threading directly to your load, paired with a 20 mm rod diameter and a NPT1/4 supply port. Travel stops rely on a fixed NBR elastomer bumper at each end, which decelerates the piston near stroke limits but is not a field-adjustable air cushion. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X35SBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 1558.6 N of extend force at 0.5 MPa to eject plastic parts from injection molding tools where axial depth is restricted by thick mold plates.
Uses the 35 mm stroke and male M18x1.5 rod end to drive a diverting flap on a packaging conveyor, securely coupling the actuator to the mechanism.
Presses small bearings into housings on an automated assembly line, relying on the fixed NBR bumper to soften the 2182 N impact at 0.7 MPa.
When sizing this 63 mm bore, stepping down to a 50 mm bore provides 981.8 N of push at 0.5 MPa, while stepping up to an 80 mm bore provides 2513.2 N of push at 0.5 MPa, giving you a clear upgrade or downgrade path for your force requirements. To confirm this exact setup, verify the 35 mm stroke, NPT1/4 port, male M18x1.5 rod thread, and the integrated sensor magnet.
Note that a standard ACQ body will not hold a load if air pressure drops or the control valve centers; the rod drifts and the fixed NBR bumper only absorbs end-of-travel impacts. For fail-safe vertical load holding, incorporate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
Quick checklist
This 63 mm bore cylinder provides 1558.6 N push and 1401.5 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. The air supply port size is NPT1/4.
No, it uses fixed NBR elastomer bumpers at both ends to absorb end-stop impacts. It is not a field-adjustable air cushion, so for high kinetic energy loads you should slow the approach speed or add an external shock absorber.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.