
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X40SBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 40mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X40SBT is a double-acting, single-rod JIS compact cylinder engineered to deliver 1558.6 N of push force and 1401.5 N of pull force at 0.5 MPa. Its short C-clip and riveted body design drastically reduces axial mounting depth compared to traditional round-body units, saving valuable machine footprint in tight assembly layouts.
This specific configuration includes a built-in piston magnet (-S) for use with AirTAC reed or electronic switches via the sensor grooves around the body, and a male M18x1.5 threaded rod end (-B) for direct load coupling. Deceleration is handled by fixed NBR elastomer bumpers at each end rather than an adjustable air cushion, meaning high-energy cycles may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X40SBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Folds and secures heavy cardboard carton flaps in continuous packaging lines, utilizing the 1558.6 N extend force to overcome board stiffness.
Pushes loaded pallets sideways onto branching conveyor tracks, where the male M18x1.5 thread provides a robust mount for the contact pad.
Ejects formed plastic parts from the lower mold half, relying on the compact body depth to fit within tight machine platen clearances.
When sizing your actuator, stepping down to the 50 mm bore yields 981.8 N of push at 0.5 MPa, while stepping up to the 80 mm bore provides 2513.2 N. The 63 mm bore hits a solid middle ground for medium-force tasks. To confirm your ordering essentials: specify the 63 mm bore, 40 mm stroke, NPT1/4 port, the S magnet option, and the B male rod thread. Note that a standard ACQ body does not hold its load if air pressure drops or the valve is centered; the rod will drift, and the fixed NBR bumper only decelerates it near the stroke end. For fail-safe positioning, an external rod lock or pilot-operated check valve is required.
Quick checklist
This 63 mm bore cylinder provides 1558.6 N push and 1401.5 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. The maximum standard stroke available for this bore is 100 mm.
No, it uses fixed NBR elastomer bumpers at the stroke ends to absorb impact. It is not an adjustable air cushion or a locking brake. For high-speed or high-energy cycles, you should slow the approach speed or add an external shock absorber.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.