
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X50BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 50mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X50BT is a double-acting JIS compact cylinder engineered to deliver a robust 1558.6 N push and 1401.5 N pull force at 0.5 MPa. By utilizing a C-clip and riveted piston-to-rod assembly, the body length is drastically reduced compared to standard round-body units, saving valuable axial mounting space in tight machinery layouts.
This specific configuration includes a male-thread piston rod end (M18x1.5) for direct mechanical coupling to your load. The 63 mm bore uses a NPT1/4 port and relies on a fixed NBR elastomer bumper at each end to absorb end-stop energy. Note that this bumper is not an adjustable air cushion, so high-velocity approaches may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X50BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides the 1558.6 N extend force needed to positively eject heavy plastic parts from mold cavities, with the male M18x1.5 thread ensuring a rigid mechanical connection to the ejector plate.
Secures stamping dies in place with 1401.5 N of retract pull at 0.5 MPa, utilizing the short C-clip body to fit within the confined column spacing of mechanical presses.
Drives heavy cardboard pallet flaps at cycle speeds up to 500 mm/s, relying on the fixed NBR bumper to absorb the impact energy at the 50 mm stroke endpoint.
When sizing this 63 mm bore, stepping down to the 50 mm bore yields 981.8 N of push force at 0.5 MPa, while stepping up to the 80 mm bore provides 2513.2 N. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. It ships without a sensor magnet, though the body retains switch grooves for future upgrades.
Keep in mind that a standard double-acting cylinder of this type does not hold its position if air pressure drops or the valve is centered; the rod will drift. If your application requires a fail-safe load hold, you must integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder generates 1558.6 N of push force and 1401.5 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates between 0.15-1.0 MPa, handles temperatures from -20 to +70 C, and runs at speeds of 30-500 mm/s.
No, it uses a fixed NBR elastomer bumper at each end rather than an adjustable air cushion, so you should slow high-energy approaches or add external shock absorbers. Additionally, this specific SKU lacks the internal magnet for position sensing, though the body still features grooves for mounting AirTAC reed or electronic switches if you add a magnet later.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.