
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X5SCBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 5mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X5SCBT is a double-acting JIS compact cylinder engineered for extreme space constraints, utilizing a short C-clip and riveted body architecture to drastically reduce axial mounting depth compared to round-body alternatives. Within this 63 mm bore, it generates a substantial 1558.6 N push force at 0.5 MPa alongside a 1401.5 N pull force, making it ideal for heavy-duty clamping over a 5 mm stroke. The hard-anodized aluminum bore ensures low friction and extended seal life.
This specific configuration includes a built-in piston magnet (-S) for non-contact position sensing via AirTAC reed or electronic switches fitted into the body grooves. It is equipped with a male-thread piston rod end (-B, M18x1.5) for secure mechanical load coupling, and utilizes a CB mounting bracket interface. Deceleration at the stroke ends is handled by fixed NBR elastomer bumpers rather than adjustable air cushions, ensuring consistent end-stop absorption without requiring manual tuning. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X5SCBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides high 1558.6 N clamping force over a short 5 mm stroke to secure injection mold halves before resin injection, preventing parting line flash.
Holds sheet metal blanks firmly against a press brake backgauge using the male M18x1.5 rod end, ensuring accurate bending alignment under heavy force.
Locks heavy machining fixtures into position on a tombstone, utilizing the CB mounting bracket to stabilize the assembly against cutting forces.
When sizing this 63 mm bore actuator, stepping down to the ACQ50 bore yields a 981.8 N push at 0.5 MPa, whereas stepping up to the ACQ80 bore provides 2513.2 N of push force at the same pressure. The 5 mm stroke is highly specialized for short clamping motions. To finalize your order, verify the 63 mm bore, 5 mm stroke, NPT1/4 port, built-in magnet (S), male M18x1.5 rod thread (B), and the CB mounting bracket. Keep in mind that a standard compact cylinder does not hold its position if air pressure drops or the directional valve is centered; the rod will drift. For fail-safe load holding, an external rod lock or a pilot-operated check valve is required.
Quick checklist
This 63 mm bore double-acting cylinder provides 1558.6 N of push force and 1401.5 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 2182 N. The maximum push force is 318 kgf at 1.0 MPa. The air supply port size is NPT1/4.
It uses fixed NBR elastomer bumpers at each end to absorb the impact at the stroke limits; these are not adjustable air cushions, so external shock absorbers may be needed for high-energy loads. The built-in magnet allows you to use AirTAC reed or electronic switches in the body grooves for end-position detection.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.