
The AirTAC ACQ Ultra Thin Air Cylinder ACQ63X70BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø63mm bore and 70mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ63X70BT is a double-acting JIS compact cylinder engineered to deliver a substantial 1558.6 N push force at 0.5 MPa and a 2182 N push at 0.7 MPa. Its short C-clip and riveted body design significantly reduce axial mounting depth compared to standard round-body units, saving valuable machine footprint in tight assemblies.
This specific configuration features a 70 mm stroke and a male M18x1.5 threaded piston rod end for direct load coupling. Deceleration is handled by a fixed NBR elastomer bumper at each end rather than an adjustable air cushion, meaning high-energy cycles may require external shock absorbers. The body includes sensor grooves, though this particular model ships without the internal magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ63X70BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø63 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 1558.6 N of extend force at 0.5 MPa to secure injection mold halves within tight machinery cavities where axial length is restricted.
Drives the folding mechanism on case erectors using its 70 mm stroke and male M18x1.5 rod end to directly push corrugated flaps at high cycle rates.
Actuates heavy routing gates on parcel sorting conveyors, relying on the fixed NBR bumper to absorb the kinetic energy of the shifting load.
For this 63 mm bore delivering 1558.6 N push at 0.5 MPa, you can step down to the 50 mm bore (981.8 N push) for lighter duties, or step up to the 80 mm bore (2513.2 N push) when higher thrust is required. When ordering, confirm the 63 mm bore, 70 mm stroke, NPT1/4 port, male M18x1.5 rod thread, and no magnet.
Keep in mind that a plain ACQ body does not hold its position if air pressure drops or the valve is centred; the piston will drift and the fixed bumper only decelerates it near the stroke end. If your application demands fail-safe load holding, an external rod lock or a pilot-operated check valve is required.
Quick checklist
The ACQ63X70BT provides a push force of 1558.6 N and a pull force of 1401.5 N at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, with a maximum push of 318 kgf at 1.0 MPa. The port size is NPT1/4, determined by the 63 mm bore.
No, it uses a fixed NBR elastomer bumper at each end to absorb end-stop impact, which is not a field-adjustable air cushion. Furthermore, it does not hold its load on air loss; the rod drifts, so an external rod lock is needed for fail-safe holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.