
The AirTAC ACQ Ultra Thin Air Cylinder ACQ80X15SBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø80mm bore and 15mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ80X15SBT is a double-acting JIS compact cylinder engineered for heavy-duty performance within a minimal axial envelope. Its C-clip and riveted piston-to-rod assembly drastically reduces overall length compared to round-body units, saving valuable machine footprint. Delivering a robust 2513.2 N push force at 0.5 MPa, it is equipped with a NPT3/8 port and a 25 mm piston rod.
This specific configuration includes an S magnet for position sensing and a B male-thread rod end (M22x1.5) for direct load coupling. Deceleration is handled by fixed NBR elastomer bumpers at both stroke ends. Because this is not an adjustable air cushion, high-energy cycles may require an external shock absorber to smoothly manage the 513 kgf maximum push capacity. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ80X15SBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø80 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M16×2.0 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Uses the 2513.2 N extend force to positively eject stamped body panels from heavy dies, leveraging the short 15 mm stroke for rapid cycling within a tight press tool.
The male M22x1.5 rod end couples directly to welding fixtures, applying high clamping pressure while the compact C-clip body minimizes the depth required inside the robotic weld cell.
Drives a short mechanical lift gate on a packaging palletizer, relying on the built-in S magnet to trigger solid-state sensors for precise load indexing at high speeds.
When sizing this 80 mm bore model, compare its 2513.2 N push at 0.5 MPa against the adjacent bores: the 63 mm variant yields 1558.6 N, while the 100 mm variant provides 3927.0 N, allowing you to step up or down based on your exact force requirements. To order, confirm the 15 mm stroke, NPT3/8 port, the required S magnet for reed or electronic switches, and the B male M22x1.5 rod thread.
Keep in mind that a standard ACQ body does not hold its position or load when air is lost or the directional valve is centred. The piston will drift, and the fixed NBR bumper only decelerates the motion near the end of travel. If your application demands a fail-safe hold under load, you must integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
This 80 mm bore double-acting cylinder provides 2513.2 N push and 2267.8 N pull at 0.5 MPa, 3518.5 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It operates at 30-500 mm/s within a 0.15-1.0 MPa pressure range.
No, the ACQ80X15SBT uses fixed NBR elastomer bumpers at each end rather than a field-adjustable air cushion. For high-speed or high-energy loads approaching the 513 kgf maximum, you should add an external shock absorber or slow the approach velocity down.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.