
The AirTAC ACQ Ultra Thin Air Cylinder ACQ80X40BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø80mm bore and 40mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ80X40BT is a double-acting single-rod JIS compact cylinder engineered to deliver substantial force within a minimal axial footprint. Utilizing a C-clip and riveted piston-to-rod assembly, the short body design significantly reduces mounting depth compared to traditional round-body units. At 0.5 MPa, this 80 mm bore configuration generates 2513.2 N of push force and 2267.8 N of pull force, peaking at a 513 kgf maximum push at 1.0 MPa.
This specific model features a male-thread piston rod end (M22x1.5) for direct, secure coupling to your tooling. The NPT3/8 porting handles the necessary air volume for the 25 mm diameter rod. Deceleration is handled by fixed NBR elastomer bumpers at both stroke ends; because these are not adjustable cushions, high-energy cycles may require external shock absorbers or a slowed approach speed. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ80X40BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø80 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M16×2.0 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Pulling heavy injection-molded automotive interior panels out of the press cavity using the 2513.2 N pull force and direct male M22x1.5 threaded rod coupling.
Ejecting stamped steel brackets from a die set, where the short JIS compact body saves valuable axial mounting depth within the press structure.
Pushing empty wooden pallets into a high-speed packaging line de-stacker, relying on the 513 kgf maximum push capacity to overcome slide friction.
When sizing this 80 mm bore model, stepping down to the 63 mm bore yields 1558.6 N of push force at 0.5 MPa, while stepping up to the 100 mm bore provides 3927.0 N. The ACQ80X40BT ships without a magnetic piston, though the body retains sensor grooves for adding switches later if needed. To order, confirm the 80 mm bore, 40 mm stroke, NPT3/8 port, male M22x1.5 rod thread, and the absence of the magnet option. Note that a standard compact cylinder drifts when air pressure is lost or the valve is centered; the fixed NBR bumper only decelerates the rod near the end of travel and does not lock the load. For fail-safe holding, an external rod lock or pilot-operated check valve is required.
Quick checklist
The ACQ80X40BT generates 2513.2 N of push force and 2267.8 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 3518.5 N. The maximum push force is 513 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a speed range of 30-500 mm/s.
No, the ACQ80X40BT uses fixed NBR elastomer bumpers at each end to absorb end-stop impact, which are not field-adjustable. Additionally, a plain double-acting cylinder does not hold its position if air is lost; the rod drifts. An external rod lock or pilot-operated check valve is required for fail-safe load holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.