
The AirTAC ACQ Ultra Thin Air Cylinder ACQ80X45ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø80mm bore and 45mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ80X45ST is a double-acting JIS compact cylinder engineered with a single rod and an 80mm bore. It generates 2513.2 N of push force and 2267.8 N of pull force at 0.5 MPa, extending to 3518.5 N push at 0.7 MPa. The C-clip and riveted piston-to-rod assembly minimize overall axial length, saving valuable mounting depth where a conventional round-body unit would protrude too far.
This 45mm stroke variant includes the S option, meaning a built-in piston magnet operates AirTAC reed or electronic switches via the sensor grooves machined around the body. End-of-travel deceleration is handled by a fixed NBR elastomer bumper at each end rather than an adjustable cushion, so high-energy cycles may require external shock absorption. The Ø25mm piston rod utilizes a female M16x2.0 thread end for straightforward load coupling. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ80X45ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø80 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M16×2.0 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides 2513.2 N of extend force at 0.5 MPa to positively eject heavy molded plastic parts from machining plates within a 45mm travel distance.
Uses the built-in S magnet with electronic switches to confirm jaw open/close positions, driving the 25mm rod to gate bar feeder material.
Applies up to 513 kgf at 1.0 MPa to seat bearings or bushings into aluminum housings, relying on the short compact body to fit tight tooling envelopes.
When sizing this 80mm bore, stepping down to a 63mm bore yields 1558.6 N push at 0.5 MPa, while stepping up to a 100mm bore provides 3927.0 N push at 0.5 MPa. This ACQ80X45ST is configured with a 45mm stroke, a NPT3/8 port, a female M16x2.0 rod thread, and the S magnet option for position sensing.
Note that a standard ACQ body lacks a physical lock; if air pressure drops or the directional valve centers, the rod will drift and the fixed NBR bumper only slows travel near the stroke ends. To maintain a fail-safe vertical or suspended load, integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
The 80mm bore generates 2513.2 N push and 2267.8 N pull at 0.5 MPa, 3518.5 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It operates between 0.15-1.0 MPa at speeds of 30-500 mm/s.
No, it uses a fixed NBR elastomer bumper at each end to absorb the end stop. It is not a field-adjustable air cushion, so for high kinetic energy loads you should slow the approach speed or add an external shock absorber.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.