
The AirTAC ACQ Ultra Thin Air Cylinder ACQ80X90BT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø80mm bore and 90mm stroke, PT3/8 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ80X90BT is a double-acting, single-rod JIS compact cylinder engineered to deliver substantial thrust in a minimal axial footprint. It generates 2513.2 N of push force and 2267.8 N of pull force at 0.5 MPa, utilizing a hard-anodized 80 mm bore for extended wear resistance. The C-clip and riveted piston-to-rod assembly significantly reduces overall length compared to conventional round-body units, saving valuable machine mounting depth.
This specific configuration includes a male-thread piston rod end (M22x1.5) for direct, secure coupling to your tooling. Deceleration at stroke ends relies on a fixed NBR elastomer bumper rather than an adjustable air cushion, meaning high-energy cycles may require external shock absorbers. The body features integrated magnetic-switch grooves, though this particular SKU ships without the sensing magnet installed. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ80X90BT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø80 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod end thread | M16×2.0 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives ejection pins on a 200-ton injection molding press, utilizing the 2513.2 N extend force to reliably strip dense plastic parts from deep steel cavities.
Actuates a heavy-duty stripper plate in a progressive stamping die, where the 90 mm stroke clears finished metal blanks from the lower die bed.
Indexes empty wooden pallets into a high-speed automated packaging line, using the male M22x1.5 rod thread to secure a robust pusher plate.
Selecting this 80 mm bore model provides 2513.2 N push at 0.5 MPa, sitting above the 63 mm option (1558.6 N push) and below the 100 mm bore (3927.0 N push) for stepping thrust capacity up or down. Operating speed spans 30-500 mm/s. Verify your ordering essentials: 80 mm bore, 90 mm stroke, NPT3/8 port, male M22x1.5 rod thread, and no sensor magnet.
Keep in mind that a standard ACQ body does not hold position upon loss of air pressure or when the valve is centered; the rod will drift, and the fixed NBR bumper only decelerates the piston near the end of travel. If your application demands a fail-safe load hold, you must incorporate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
At 0.5 MPa, this 80 mm bore cylinder provides 2513.2 N of push force and 2267.8 N of pull force. At 0.7 MPa, the push force reaches 3518.5 N, with a maximum push capacity of 513 kgf at 1.0 MPa. Operating pressure ranges from 0.15-1.0 MPa, and the speed range is 30-500 mm/s.
No, the ACQ80X90BT uses a fixed NBR elastomer bumper at each end to absorb end-stop impact, not an adjustable air cushion. For high-speed or high-mass loads, you should add an external shock absorber or throttle the approach speed. Additionally, this model uses a male M22x1.5 rod thread and lacks a factory-installed sensor magnet.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.