The AirTAC SCJ63 Standard Cylinder SCJ63X135-50 is a genuine double-acting DOUBLE-ROD air cylinder whose rear rod carries the stroke ADJUSTER: the stroke end is field-adjustable within a 50 mm range without swapping the cylinder. Ø63mm bore, 135mm nominal stroke, PT1/4 ports and adjustable end cushioning.
The AirTAC SCJ63X135-50 is a double-acting, double-rod pneumatic cylinder with a rear-cap adjusting screw that provides a 50 mm field-adjustable stroke end. This adjustable-stroke design allows machine builders to fine-tune the end position without swapping the cylinder, making it ideal for commissioning trials and format changeovers.
With a 135 mm nominal stroke and a 28 mm air cushion, this SCJ model decelerates the piston smoothly near the stroke end, protecting end caps. The body length A is 197 mm, and the cylinder is rated for standard operating pressures from 0.15 to 1.0 MPa. It uses the default TPU seal for a temperature range of -20 to +70 °C and comes with PT threads in a basic mounting configuration, ready to accept the SCJ subset of mounting accessories.
| Model | Airtac SCJ63 Standard Cylinder SCJ63X135-50 |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 135 mm |
| Stroke adjustment | Up to 50 mm (rear adjusting screw) |
| Acting type | Double acting (double rod) |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The adjuster on the rear rod sets the stroke end position. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SCJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SC push of the same bore. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×135 | Nominal (maximum) stroke length in mm. |
| -50 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The 50 mm rear adjustment screw lets technicians precisely dial in the actuator end-stop during initial machine setup without changing hard stops or linkages.
Quickly adjust the stroke end for different product sizes on packaging or sorting lines, reducing downtime between production runs with a simple screw turn.
As tooling or gripper pads wear over time, the adjustable stroke can be extended slightly to maintain precise contact and consistent cycle quality.
For less force, the SCJ50 provides 982 N. This adjustable-stroke model is the right pick when you need to dial in the stroke end position on the machine; if a fixed, repeatable stroke is sufficient, the standard SC series is a more economical choice. For a direct replacement, match the 63 mm bore, 135 mm nominal stroke, 50 mm adjust range, PT port thread, and basic mounting. If you later need position sensing, a magnet-equipped version can be ordered.
AirtacDistr lists every SCJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-scj63-adjustable-cylinder
Adjustable-stroke checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. The pull force is lower due to the area of the 20 mm single piston rod. The maximum push force at the 0.9 MPa operating limit is 2805 N.
A rear-cap screw shortens the stroke end by up to 50 mm from the 135 mm nominal maximum. It replaces another SCJ of the same bore, nominal stroke, and adjust range. It cannot directly replace a fixed-stroke SC cylinder without checking if the slightly longer body length and rear screw clearance are acceptable.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.