
The AirTAC SCJ100 Standard Cylinder SCJ100X75-30 is a genuine double-acting DOUBLE-ROD air cylinder whose rear rod carries the stroke ADJUSTER: the stroke end is field-adjustable within a 30 mm range without swapping the cylinder. Ø100mm bore, 75mm nominal stroke, PT1/2 ports and adjustable end cushioning.
The SCJ100X75-30 is a double-acting, double-rod pneumatic cylinder that delivers substantial force in a compact tie-rod body, with a rear adjusting screw providing up to 30 mm of fine-tuned stroke-end control.
The 100 mm bore houses a 25 mm diameter piston rod and breathes through PT1/2 ports, with an adjustable air cushion absorbing end-of-stroke impact over a 29 mm cushion length. The body length A(SCJ) is 245 mm for the base cylinder, and the field-adjustable stroke end lets you shorten the 75 mm nominal stroke by up to 30 mm without swapping the cylinder or adding external hard stops.
| Model | Airtac SCJ100 Standard Cylinder SCJ100X75-30 |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 75 mm |
| Stroke adjustment | Up to 30 mm (rear adjusting screw) |
| Acting type | Double acting (double rod) |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The adjuster on the rear rod sets the stroke end position. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
SCJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SC push of the same bore. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Nominal (maximum) stroke length in mm. |
| -30 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Dial in the exact end-of-stroke position during machine setup without machining new stops. The 30 mm adjustment range on the SCJ100X75-30 lets commissioning engineers quickly compensate for stack-up tolerances in weldments or fabricated frames.
As gripper pads or clamp faces wear over thousands of cycles, the adjustable screw can be turned to restore the original clamping gap, keeping cycle time and part quality consistent without replacing the cylinder or tooling.
When a packaging line switches between product sizes, the SCJ100X75-30 allows operators to quickly adjust the push stroke for different box heights or pallet layers, reducing changeover time compared to fixed-stroke cylinders.
Choose a fixed-stroke SC cylinder when the stroke never changes, or a guided cylinder if the 75 mm stroke and 25 mm rod risk side-load deflection. A direct replacement must match the 100 mm bore, 75 mm nominal stroke, 30 mm adjust range, PT1/2 ports, and basic mounting; add the -S suffix if a magnet is needed for barrel-mounted sensors.
AirtacDistr lists every SCJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-scj100-adjustable-cylinder
Adjustable-stroke checklist
At the maximum operating pressure of 1.0 MPa, the theoretical push force reaches 7854 N. Always size for the pull force if the cylinder must retract a load.
A rear-cap adjusting screw sets the stroke end position, letting you shorten the 75 mm nominal stroke by up to 30 mm. Pick the SCJ when you need to fine-tune the stop point during commissioning, accommodate tooling wear, or handle frequent format changes. Choose a fixed-stroke SC if the stroke is permanently fixed, as it is simpler and slightly shorter in overall length.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.