The AirTAC SCJ80 Standard Cylinder SCJ80X30-30 is a genuine double-acting DOUBLE-ROD air cylinder whose rear rod carries the stroke ADJUSTER: the stroke end is field-adjustable within a 30 mm range without swapping the cylinder. Ø80mm bore, 30mm nominal stroke, PT3/8 ports and adjustable end cushioning.
The SCJ80X30-30 is an 80 mm bore double-acting double-rod cylinder that puts field-adjustable stroke control directly on the machine. Its rear-cap adjusting screw lets you shorten the stroke end by up to 30 mm, so the effective stroke is tunable from 0 to 30 mm without removing the cylinder or adding external hard stops.
This tie-rod cylinder uses an adjustable air cushion (28 mm length) for smooth end-of-stroke deceleration and operates on 40 µm filtered air from 0.15 to 1.0 MPa. The SCJ body length A is 239 mm, slightly longer than a fixed-stroke SC of the same bore to house the adjustment mechanism. Standard speed range is 30-800 mm/s, and the temperature window is -20 to +70 °C with the default TPU seals.
| Model | Airtac SCJ80 Standard Cylinder SCJ80X30-30 |
|---|---|
| Series | SCJ adjustable-stroke tie-rod cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 30 mm |
| Stroke adjustment | Up to 30 mm (rear adjusting screw) |
| Acting type | Double acting (double rod) |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The adjuster on the rear rod sets the stroke end position. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SCJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SC push of the same bore. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
| SCJ | Adjustable-stroke tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Nominal (maximum) stroke length in mm. |
| -30 | Adjustable-stroke range in mm (options 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
During machine bring-up, the -30 mm adjust screw lets technicians dial in the exact stroke end position for gripper close, clamp engagement, or ejector depth without fabricating new stops or swapping cylinders.
On packaging or assembly lines running multiple product sizes, operators can quickly reset the stroke end for different box heights, pallet widths, or component thicknesses using only a wrench on the rear cap screw.
In high-cycle pressing or clamping stations, the adjustable stroke end takes up mechanical wear in tooling or seals over time, maintaining consistent contact force and part quality without replacing the actuator.
The SCJ is the right pick when you need to fine-tune the stroke end position during commissioning, format changes, or wear take-up—if your stroke is fixed and never needs field adjustment, the standard SC fixed-stroke cylinder is a simpler, lower-cost alternative. For a direct replacement, match an AirTAC SCJ80 cylinder with a 30 mm nominal stroke, a -30 adjust range, PT3/8 ports, and the same basic mounting configuration. For strokes of 300 mm or more, evaluate side-loading and rod buckling; an external guide rail or a guided cylinder may be required.
AirtacDistr lists every SCJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-scj80-adjustable-cylinder
Adjustable-stroke checklist
At the maximum operating pressure of 0.9 MPa, push force reaches 4523 N. The theoretical maximum at 1.0 MPa is 513 kgf.
A rear-cap adjusting screw sets the stroke end position within a 30 mm range; the nominal 30 mm stroke is the maximum. This lets you fine-tune the stopping point on the machine. Choose SCJ when you need field-adjustable stroke for commissioning, format changes, or wear take-up. Choose the fixed-stroke SC when the stroke is permanently set and you want a simpler, lower-cost cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.