verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SCJ Series · Adjustable-Stroke Cylinder

Airtac SCJ80 Standard Cylinder SCJ80X75-10

The AirTAC SCJ80 Standard Cylinder SCJ80X75-10 is a genuine double-acting DOUBLE-ROD air cylinder whose rear rod carries the stroke ADJUSTER: the stroke end is field-adjustable within a 10 mm range without swapping the cylinder. Ø80mm bore, 75mm nominal stroke, PT3/8 ports and adjustable end cushioning.

  • BoreØ80 mm
  • Nominal stroke75 mm
  • Stroke adjust-10 mm
  • Port sizePT3/8
  • Rod threadM20×1.5
  • CushionAdjustable, 28 mm
$103.98 $111.48Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SCJ80 stroke, mounting and version on one page All SCJ80 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SCJ80 Standard Cylinder SCJ80X75-10

The SCJ80X75-10 is an 80 mm bore double-acting double-rod cylinder with a field-adjustable stroke end, providing up to 10 mm of fine-tuning via a rear-cap screw.

This tie-rod cylinder uses a 25 mm rod and PT3/8 ports, with a 28 mm air cushion at each end for controlled deceleration. The body length A(SCJ) is 239 mm, slightly longer than a fixed-stroke SC of the same bore to accommodate the adjusting mechanism. It operates from 0.15 to 1.0 MPa and suits speeds of 30-800 mm/s.

Airtac SCJ80 Standard Cylinder SCJ80X75-10 Technical Specifications

ModelAirtac SCJ80 Standard Cylinder SCJ80X75-10
SeriesSCJ adjustable-stroke tie-rod cylinder
Bore sizeØ80 mm
Nominal stroke75 mm
Stroke adjustmentUp to 10 mm (rear adjusting screw)
Acting typeDouble acting (double rod)
Port sizePT3/8
Rod threadM20×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 800 mm/s
CushionAdjustable, 28 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SCJ (adjustable-stroke) datasheet. The adjuster on the rear rod sets the stroke end position. Confirm against the product label before installation. Thread options: PT (standard) / G.

Theoretical Output Force (Ø80mm)

PressurePush forcePull force
0.5 MPa2268 N2268 N
0.7 MPa3175 N—
Max (@1.0 MPa)463 kgf

SCJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SC push of the same bore. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.

Model Code: Airtac SCJ80 Standard Cylinder SCJ80X75-10

SCJAdjustable-stroke tie-rod cylinder series.
80Bore size in mm.
×75Nominal (maximum) stroke length in mm.
-10Adjustable-stroke range in mm (options 10/20/30/40/50/75/100).
-SOptional built-in magnet for sensor position sensing.

Related types: SC (single rod, fixed stroke), SCD (double rod), SCT (multi-position). SCJ mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.

Where the Airtac SCJ80 Standard Cylinder SCJ80X75-10 Is Used

tune

Commissioning Fine-Tuning

During machine setup, the 10 mm adjust range lets technicians dial in the exact end-stop position for gripper closure or part placement without re-machining brackets or swapping cylinders.

conveyor_belt

Format Changeover Stops

On packaging lines running multiple box sizes, the rear screw quickly shifts the stroke end to match a new product width, reducing changeover time compared to fixed mechanical stops.

settings

Wear Take-Up in Clamping

In repetitive clamping fixtures, the adjustable stroke compensates for jaw or pad wear over time, maintaining consistent clamp force without replacing the actuator or adding shims.

Is the Airtac SCJ80 Standard Cylinder SCJ80X75-10 the Right Cylinder?

If your application does not require field stroke adjustment, the fixed-stroke SC80X75 is a simpler, cost-effective alternative. For guided loads or high side-force moments, pair the cylinder with an external guide or consider a guided cylinder.

A direct replacement must match the 80 mm bore, 75 mm nominal stroke, 10 mm adjust range, PT3/8 ports, and basic mounting configuration. This model is built without a magnet; if position sensing is needed, order the -S variant and add CMSG/DMSG sensors.

AirtacDistr lists every SCJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-scj80-adjustable-cylinder

Adjustable-stroke checklist

  • ✓ Need to fine-tune stroke on the line?
  • ✓ Nominal stroke + adjust range (-10)
  • ✓ Required force at your working pressure
  • ✓ Port/thread type (PT/NPT/G)
  • ✓ Magnet (-S) for sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the rear adjusting screw, then lock it before running.
  • check Adjust end cushion screws for smooth stops.
  • check Use SCJ mounting accessory (FA / LB / TC / TCM1).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SCJ80 Standard Cylinder SCJ80X75-10 FAQ

At the maximum operating pressure of 1.0 MPa, push force reaches 4523 N.

Yes, if you need the 10 mm stroke-end adjustment feature. The SCJ shares the same bore, rod, port, and mounting accessories as the SC80, but the body is slightly longer. Ensure the extra length and the rear adjusting screw fit your machine envelope.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SCJ Adjustable-Stroke Cylinders

Request a Quote for Airtac SCJ80 Standard Cylinder SCJ80X75-10

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SCJ80X75-10 and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.