
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X55-40 is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 15 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X55-40 is a compact double-acting double-rod cylinder featuring an external M5x0.8 adjuster screw that dials the extend stop directly on your machine. You can set the outward stroke anywhere between 15 and 55 mm without swapping shims or parts.
The short riveted body drastically cuts axial mounting depth, fitting where round-body or profile cylinders cannot. End-of-stroke deceleration relies on a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches; adding the -S option enables sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X55-40 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 55 mm |
| Adjustable range | 15 – 55 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 15 to 55 mm extend stop during prototype runs. The external screw allows instant length tweaks without disassembling the fixture.
Switch between part families on a packaging line by turning the M5x0.8 adjuster.
Fit the short riveted body into tight machine cells to push small components. The fixed NBR bumper absorbs the impact of rapid ejections.
Choose the 16 mm if you need that middle ground of force in a tight footprint.
The 40 mm adjustment window is perfect for setups requiring frequent trial positioning or rapid product changeover. Remember that a plain cylinder drifts when air is lost or the valve centers—the fixed bumper only decelerates near the end and is not a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve. This configuration includes a 55 mm stroke, 40 mm window, M5x0.8 port, female M3x0.5 rod thread, and no magnet.
AirtacDistr lists every SDAJ16 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj16-adjustable-cylinder
Quick checklist
It operates at 30-500 mm/s, accepts 0.15-1.0 MPa air pressure, and functions from -20 to +70 C.
Turning the R (M5x0.8) screw shortens the extend stroke by up to 40 mm, giving a usable 15-55 mm range. The screw sets a mechanical stop and does not alter force. It is not a mid-stroke lock; the cylinder will drift if air is lost, so use an external rod lock for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.