
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X55-40B is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 15 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X55-40B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M5x0.8) screw, you can dial the forward end-position anywhere between 15 and 55 mm directly on your equipment, eliminating the need for shims or part swaps during setup.
Its short riveted body drastically reduces axial mounting depth, fitting easily into tight spaces where larger profile cylinders cannot. This specific SKU includes a male-thread M5x0.8 piston rod (option B) for secure external attachment, and it relies on a fixed NBR bumper at each end to decelerate the stroke. Note that this variant lacks a piston magnet, so it cannot support reed or electronic sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X55-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 55 mm |
| Adjustable range | 15 – 55 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the probe extension in 16 mm bore test rigs where space is tight, using the compact riveted body to fit within dense experimental setups without adding axial bulk.
When sizing this unit, evaluate your force requirements against its neighbours.
Choose this model if your application requires frequent on-machine stroke tuning between 15 and 55 mm to accommodate different part heights. Confirm your required 16 mm bore, 55 mm maximum stroke, 40 mm adjustment window, M5x0.8 air port, male M5x0.8 rod thread, and the absence of a magnet. Remember that a plain cylinder does not hold position or load when air is lost or the valve is centred; the bumper only decelerates near the end of travel. For secure load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ16 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj16-adjustable-cylinder
Quick checklist
The adjustable stop does not alter these force values.
The R (M5x0.8) screw mechanically shortens the extend stroke from the 55 mm maximum down to 15 mm. It is strictly a mechanical end-stop, not a mid-stroke lock. The cylinder cannot hold a load if air pressure is lost; use an external rod lock or pilot-operated check valve for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.