
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X60-10B is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 50 to 60 mm on the machine — no shims, no part change.
The SDAJ16X60-10B is a compact double-acting double-rod cylinder featuring an external M5x0.8 R screw that lets you dial the extend stop directly on your machine between 50 and 60 mm. The short riveted body minimizes axial mounting depth where a round-body or profile cylinder will not fit.
This specific SKU includes a male M5x0.8 piston rod thread and lacks a piston magnet, meaning it cannot accept magnetic switches. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed ranges from 30 to 500 mm/s.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X60-10B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 60 mm |
| Adjustable range | 50 – 60 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the 50-60 mm extend stop during initial tooling commissioning to strike parts precisely without machining custom shims.
Fine-tune the extend endpoint in 5.1 kg vertical lift test rigs to find the optimal contact depth before locking down the final design.
When sizing this actuator, evaluate your force requirements bidirectionally. Dropping to a 12 mm bore reduces the 0.5 MPa push to 56.5 N, whereas stepping up to a 20 mm bore increases it to 157.1 N.
This model is ideal for operators needing on-site stroke tuning without part changes, but remember that a plain cylinder does not hold its load on air loss or valve centering. The piston will drift, and the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve. Confirm your bore, 60 mm maximum stroke, 10 mm adjust window, M5x0.8 port, male M5x0.8 rod, and lack of magnet before ordering.
AirtacDistr lists every SDAJ16 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj16-adjustable-cylinder
Quick checklist
At 0.7 MPa the push is 140.7 N and pull is 121 N. The theoretical maximum push is 21 kgf at 1.0 MPa.
The M5x0.8 R screw mechanically shortens the extend stroke from the 60 mm maximum down to 50 mm. It does not alter force or lock mid-stroke. Because this SKU lacks the -S magnet, it cannot accept reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.