
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X60-20 is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 40 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X60-20 is a compact double-acting double-rod cylinder featuring an external M5x0.8 adjuster screw. This mechanism lets you dial the extend stop down from the 60mm maximum to any point between 40 and 60mm directly on the machine, eliminating the need for shims or part swaps during changeovers. The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit.
End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X60-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 60 mm |
| Adjustable range | 40 – 60 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 40 and 60mm on the fly to accommodate different part lengths without swapping out the entire actuator assembly.
Use the M5x0.8 adjuster screw to fine-tune the extension endpoint during R&D testing until the precise 60N working contact point is found.
When sizing this 16mm bore, evaluate your force requirements both ways. Choose this 40-60mm adjustable unit if your fixture requires frequent trial positioning or rapid format changes.
Confirm your parameters: 16mm bore, 60mm maximum stroke, 20mm adjust window, and an M5x0.8 air port. This configuration has a female M3x0.5 rod-end thread and no magnet. Remember that a plain cylinder does not hold a load if air pressure drops or the valve is centred; the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ16 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj16-adjustable-cylinder
Quick checklist
It operates between 0.15 and 1.0MPa, tolerates temperatures from -20 to +70C, and runs at speeds of 30-500mm/s.
Turning the external R (M5x0.8) screw mechanically shortens the extend endpoint within a 40 to 60mm window without altering the force. The screw acts only as a stop and does not lock the piston mid-stroke; if air is lost, the cylinder drifts. For load holding, you need an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.