
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-40S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 25 to 65 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X65-40S is a compact double-acting double-rod cylinder featuring an external extend stop. An M6x1.0 adjuster screw lets you dial the forward stroke down from the 65 mm maximum to as little as 25 mm directly at the machine, eliminating the need for shims or part swaps during changeovers.
This model includes a built-in piston magnet for AirTAC reed or electronic switches and uses an M5x0.8 air port. Its short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 65 mm |
| Adjustable range | 25 – 65 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 25 to 65 mm extend stop during prototype runs.
Swap product variants on the fly by turning the external adjuster. The compact riveted body fits tight tooling spaces while maintaining a full 65 mm maximum retract stroke.
Adjust the extend position on packaging equipment to accommodate different carton depths. The fixed NBR bumper reliably absorbs the end shock for each newly set stop point.
When sizing this 20 mm bore actuator, consider the neighbouring bores to ensure optimal performance. Choose this specific unit if your fixture requires frequent, on-site stroke tuning within the 25 to 65 mm window.
Confirm the bore, 65 mm maximum stroke, 40 mm adjust window, M5x0.8 port, and the female M4x0.7 rod-end thread suit your mounting interface. The -S suffix indicates the magnet is present for position sensing. Note that a plain cylinder does not hold a load if air pressure drops or the valve is centered; the fixed bumper only decelerates near the end of travel and is not a lock. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ20 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj20-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 219.9 N. The theoretical maximum push force is 32 kgf at 1.0 MPa.
The M6x1.0 R screw shortens the extend stroke by up to 40 mm, allowing you to set the forward stop anywhere between 25 and 65 mm. The included -S magnet enables position detection using AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.