
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X150-50S is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 100 to 150 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X150-50S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M10x1.25) screw, you shorten the forward stroke on-site across a 100 to 150 mm window without swapping shims or parts.
This 32 mm bore actuator carries a built-in piston magnet (-S) for direct mounting of AirTAC reed or electronic switches along the body grooves. Its short riveted body saves axial mounting depth where a larger profile cylinder will not fit. Note that the 150 mm length is a non-standard made-to-order stroke exceeding the 130 mm standard maximum for this bore. End-of-travel deceleration relies on a fixed NBR bumper, not an adjustable air cushion.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X150-50S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 150 mm |
| Adjustable range | 100 – 150 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 100 to 150 mm during changeovers to accommodate different raw material widths without fabricating custom spacers.
Use the on-site tuning capability to test various extend endpoints safely, knowing the fixed NBR bumper absorbs end-shock during trial cycles.
When sizing this unit, evaluate both neighbouring bores against your actual load requirements. Choose this specific model if your fixture requires on-site extend tuning across that 100 to 150 mm range.
Confirm the 32 mm bore, 150 mm maximum stroke, 50 mm adjustment window, and PT1/8 air port for your plumbing. The -S code ensures compatibility with solid-state or reed sensors, while the female M6x1.0 rod-end thread dictates your mounting interface. Remember that a plain cylinder does not hold position on air loss or when the valve is centred; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, specify an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj32-adjustable-cylinder
Quick checklist
The theoretical maximum push is 82 kgf at 1.0 MPa. Adjusting the stroke does not alter these force figures.
The R (M10x1.25) screw mechanically shortens the extend endpoint anywhere between 100 and 150 mm. The -S suffix indicates a built-in piston magnet, allowing you to fit AirTAC reed or electronic switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.