
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X80-20SB is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 60 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X80-20SB is a compact double-acting double-rod cylinder featuring an on-site adjustable extend stop. By turning the external M10x1.25 adjuster screw, you can tune the forward stroke anywhere between 60 and 80 mm without changing parts.
This variant includes a built-in piston magnet (-S) for direct mounting of AirTAC reed or electronic switches, and a male M10x1.25 piston rod end (-B) for secure external attachment. The short riveted body minimizes axial footprint, while a fixed NBR bumper at each end absorbs end-of-travel shock. Operating speed spans 30-500 mm/s across a 0.15 to 1.0 MPa pressure range.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X80-20SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 80 mm |
| Adjustable range | 60 – 80 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the mechanical stop on the fly when switching production lines, relying on the male M10x1.25 rod to drive a sorting flap.
Use the integrated magnet with an electronic switch to verify the extended position while fine-tuning the end stop for a delicate testing array.
When sizing this 32 mm bore unit, evaluate your force requirements carefully. It is ideal for setups requiring frequent changeovers or trial positioning.
Confirm the 32 mm bore, 80 mm maximum stroke, 20 mm adjustment window, PT1/8 air port, male M10x1.25 rod thread, and integrated magnet. Remember that a plain compact cylinder cannot hold a load if air pressure drops or the valve is centered; the piston will drift. For suspended loads, integrate an external rod lock or a pilot-operated check valve, as the fixed NBR bumper only decelerates near the end of travel and does not act as a brake.
AirtacDistr lists every SDAJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj32-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 563 N and pull to 483.8 N. The theoretical maximum push is 82 kgf at 1.0 MPa.
The external M10x1.25 screw lets you shorten the extend stroke from the 80 mm maximum down to 60 mm on the machine. The built-in magnet (-S) allows you to mount AirTAC reed or electronic solid-state switches directly into the body grooves for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.