
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X110-40B is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 70 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X110-40B is a double-acting compact cylinder featuring an external M12x1.25 adjuster screw that lets you dial the extend stop directly on your machine between 70 and 110 mm.
Its short riveted body drastically cuts axial mounting depth where round-body or larger profile units will not fit. This specific SKU includes a male M14x1.5 piston rod end and lacks a piston magnet, meaning it cannot host reed or electronic switches without upgrading to the -S variant. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but does not function as an adjustable air cushion.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X110-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 110 mm |
| Adjustable range | 70 – 110 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 70 to 110 mm during fixture swaps to accommodate varying part heights without machining new spacers.
Set a precise mechanical stop for pressing bearings, ensuring the male M14x1.5 rod retracts fully while avoiding over-travel.
If your application requires less force, stepping down to an SDAJ32 yields 402.1 N at 0.5 MPa, while moving up to an SDAJ50 provides 981.7 N for heavier demands. This 40 mm bore is ideal for operators needing frequent on-machine stroke tuning during changeovers without swapping components.
Confirm your parameters before ordering: 40 mm bore, 110 mm maximum stroke, 40 mm adjustment window, PT1/8 port, and the male M14x1.5 rod thread (-B). Note that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj40-adjustable-cylinder
Quick checklist
The air port is PT1/8.
Turning the external R (M12x1.25) screw shortens the extend stroke by up to 40 mm, giving a usable range of 70 to 110 mm. This specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches; you must select the -S option for sensing capabilities.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.