
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X55-40S is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 15 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X55-40S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M12x1.25) adjuster screw, you can dial the forward end-position down by up to 40 mm directly on the machine, yielding a usable extend range of 15 to 55 mm without swapping shims or parts.
This unit includes a built-in piston magnet (-S) for AirTAC reed or electronic solid-state switches housed in the body sensor grooves. The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit. End shock is managed by a fixed NBR bumper that decelerates the stroke, which is not an adjustable air cushion.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X55-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 55 mm |
| Adjustable range | 15 – 55 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the pusher extension on-site via the M12x1.25 screw to deflect different carton widths off a belt while keeping the compact riveted body within tight axial confines.
Set a precise mechanical lower stop for a 32 kg lift payload, relying on the fixed NBR bumper to decelerate the approach rather than risking hard bottoming.
Choose this specific unit if your fixture requires frequent on-machine stroke tuning during changeovers.
Confirm the 40 mm bore, 55 mm maximum stroke, 40 mm adjustment window, and PT1/8 air port. The -S magnet is present for position sensing, and the rod-end thread is female M8x1.25. Note that a plain cylinder does not hold its load on air loss or when the valve is centred; the piston drifts and the bumper only decelerates near the end. For a held load without live pressure, specify an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj40-adjustable-cylinder
Quick checklist
The adjustment screw sets the stop position and does not alter these force values.
The external M12x1.25 adjuster screw shortens the extend stroke by up to 40 mm, allowing you to set the forward stop anywhere between 15 and 55 mm. The included -S magnet enables position detection using AirTAC reed or electronic solid-state switches mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.