
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X110-100S is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 10 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X110-100S is a double-acting, double-rod compact cylinder featuring an external adjustable extend stop. An M16x1.5 adjuster screw lets you dial the outward stroke anywhere between 10 and 110 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
Built with a space-saving riveted body, this unit fits where longer profile or round-body cylinders cannot. It includes a fixed NBR bumper at each end to decelerate the stroke end, though this is not an adjustable air cushion. The -S suffix denotes a built-in piston magnet for position sensing with AirTAC reed or electronic switches.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X110-100S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 110 mm |
| Adjustable range | 10 – 110 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 100 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -100 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 10 to 110 mm via the M16x1.5 screw to set precise pressing depths for varying component heights without machining new spacers.
Safely lift loads up to 50 kg in vertical applications, tweaking the mechanical stop height during commissioning while relying on the fixed NBR bumper for end deceleration.
Choose this specific model if your fixture setup requires frequent trial positioning or on-site stroke tuning across a wide 100 mm window.
Confirm your parameters: 50 mm bore, 110 mm max stroke, 100 mm adjust window, PT1/4 port, built-in magnet (S), and a female M10x1.5 rod-end thread. Note that a plain cylinder does not hold its load on air loss or when the valve is centred—the piston drifts and the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
The theoretical maximum push is 200 kgf at 1.0 MPa. The adjustable stop does not alter these force values.
Turning the external R (M16x1.5) screw shortens the extend stroke by up to 100 mm, giving a usable range of 10 to 110 mm. The -S suffix means a piston magnet is built in for position detection using AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.