
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X110-75S is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 35 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X110-75S is a double-acting compact cylinder featuring an external M16x1.5 adjustment screw that lets you dial the extend stop anywhere between 35 and 110 mm directly on the machine.
Its short riveted body saves valuable axial mounting depth where a longer conventional cylinder would fail to fit. End-of-stroke deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, and the included -S piston magnet supports position sensing with AirTAC reed or electronic switches.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X110-75S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 110 mm |
| Adjustable range | 35 – 110 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 35 to 110 mm during product changeovers to position machining heads without fabricating new mechanical spacers.
Safely test vertical lifts of approximately 50 kg by fine-tuning the extend position on-site before finalizing the mechanical hard stops.
Choose the SDAJ50X110-75S specifically when your fixture requires frequent on-site stroke tuning across a wide 75 mm window.
Confirm your parameters: 50 mm bore, 110 mm max stroke, 75 mm adjust window, PT1/4 port, built-in magnet (S), and a female M10x1.5 rod-end thread. Remember that a plain cylinder drifts when air is lost or the valve is centered—the fixed bumper only decelerates near the end of travel and does not lock the load. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 1374.4 N and pull to 1154.5 N. The theoretical maximum push is 200 kgf at 1.0 MPa.
The M16x1.5 R screw mechanically shortens the extend stroke by up to 75 mm, allowing an effective extend range of 35 to 110 mm without changing force. The built-in -S magnet enables position detection using either AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.