
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X130-75B is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 55 to 130 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X130-75B is a compact double-acting cylinder with a 50 mm bore and a male-thread piston rod (M18x1.5). It features an external M16x1.5 adjuster screw that lets you dial the extend end-position anywhere between 55 and 130 mm directly on the machine, avoiding part swaps during changeovers. Retract remains at the full 130 mm stroke.
The short riveted body minimizes axial mounting depth where space is tight. End-of-travel deceleration is handled by a fixed NBR bumper, which is not an adjustable air cushion or a locking device.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X130-75B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 130 mm |
| Adjustable range | 55 – 130 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×130 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the stroke length on-site during product format changes to reposition diverter gates precisely along the belt line.
Choose this specific bore if your setup-heavy line requires frequent on-machine stroke tuning between 55 and 130 mm.
Verify your requirements against the configuration: a 50 mm bore, 130 mm maximum stroke with a 75 mm adjustment window, PT1/4 air port, and a male M18x1.5 rod end. Note that this SKU lacks a piston magnet, so it cannot accept reed or electronic switches without upgrading to the -S variant. A plain cylinder does not hold position on air loss or valve centering; the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
Turning the external M16x1.5 screw shortens the extend stop by up to 75 mm, yielding a usable extend range of 55 to 130 mm. The screw acts as a mechanical stop and does not alter the output force.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.