
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X25-20 is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 5 to 25 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X25-20 is a double-acting compact cylinder featuring an external M16x1.5 R-thread adjustment screw that dials the extend stop directly on your machine. You can tune the outward stroke anywhere between 5 and 25 mm without swapping shims or parts, while the retract motion remains full length.
Its short riveted body saves valuable axial mounting depth where round-body or larger profile cylinders will not fit. End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion, meaning the stop absorbs shock but does not act as a mid-stroke lock. Note this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X25-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 25 mm |
| Adjustable range | 5 – 25 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 5 to 25 mm to clamp varying raw castings on a single fixture, avoiding the need to swap physical spacer rings during changeover.
Fine-tune the rod extension precisely into the 5-25 mm window to fold differing cardboard thicknesses without crushing the material.
Choose this model if your fixture requires frequent on-site stroke tuning to accommodate varied part heights.
Confirm your parameters before ordering: 50 mm bore, 25 mm maximum stroke, 20 mm adjust window, PT1/4 port, female M10x1.5 rod-end thread, and no magnet. Remember that a plain cylinder does not hold its load if air pressure drops or the valve centres—the piston will drift. For suspended or gravity-loaded applications, integrate an external rod lock or pilot-operated check valve, as the fixed NBR bumper only decelerates near the end of travel and never brakes mid-stroke.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
The theoretical maximum push is 200 kgf at 1.0 MPa.
Turning the external R (M16x1.5) screw shortens the extend end-position by up to 20 mm, giving a usable outward stroke of 5 to 25 mm. This specific SKU lacks a piston magnet; to use reed or electronic switches, you must select the -S magnet option.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.