
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X55-30 is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 25 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X55-30 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M16x1.5 adjuster screw lets you dial the extend position down from the 55mm maximum to 25mm directly on the machine, eliminating the need for shims or part swaps.
Built with a short riveted body, this unit saves valuable axial mounting depth where a larger profile cylinder will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X55-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 55 mm |
| Adjustable range | 25 – 55 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 55mm down to 25mm via the M16x1.5 screw to accommodate different part heights during machine changeovers without machining new spacers.
Fine-tune the extend position on-site during carton size trials, using the fixed NBR bumper to absorb the end shock while finding the optimal folding depth.
When sizing this 50mm bore, evaluate your force requirements against its neighbours.
This model is ideal for setups requiring frequent on-site stroke tuning between 25 and 55mm. Remember that a plain cylinder does not hold its load if air pressure drops or the valve is centred; the fixed bumper only decelerates near the end of travel and the M16x1.5 screw is a mechanical stop, not a mid-stroke lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve. Confirm your bore, 30mm adjustment window, PT1/4 port, and female M10x1.5 rod-end thread before ordering.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 1374.4 N. The theoretical maximum push is 200 kgf at 1.0 MPa.
The external M16x1.5 screw shortens the extend stroke by up to 30mm, allowing you to set the stop anywhere between 25mm and 55mm. It is strictly a mechanical stop and does not function as a mid-stroke lock; the cylinder cannot hold a load if air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.