
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X55-50 is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 5 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X55-50 is a double-acting compact cylinder featuring a 50mm external adjustment window, allowing you to dial the extend stop anywhere from 5 to 55mm directly at the machine.
Its short riveted body minimizes axial mounting depth, fitting where larger profile cylinders cannot. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X55-50 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 55 mm |
| Adjustable range | 5 – 55 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 5-55mm extend stop during initial tooling setups to find the exact contact point without machining custom spacers.
Adjust the pusher extension on the fly to accommodate varying carton widths on a single packaging line.
When sizing this unit, consider the SDAJ40 if your layout permits, which steps the push force down to 628.3 N at 0.5 MPa. Conversely, moving up to the SDAJ63 provides a substantial increase to 1558.6 N at 0.5 MPa for heavier payloads. The SDAJ50X55-50 is ideal for operators needing frequent on-machine stroke tuning during format changeovers without swapping components.
This configuration uses a PT1/4 port, a 20mm piston rod with a female M10x1.5 thread, and the M16x1.5 R adjuster screw. Keep in mind that a plain cylinder does not hold its load if air pressure drops or the valve centers; the piston will drift. For suspended or vertical loads requiring fail-safe holding, you must integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 1374.4 N and pull to 1154.5 N. The theoretical maximum push is 200 kgf at 1.0 MPa.
The M16x1.5 R adjuster screw mechanically shortens the extend stroke by up to 50mm, allowing usable travel between 5 and 55mm. It sets the stop position only and does not alter the output force or lock the piston mid-stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.