
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X65-10SB is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 55 to 65 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X65-10SB is a double-acting, double-rod compact cylinder featuring an on-site extend stop. By turning the external R (M16x1.5) screw, you can dial the forward stroke down from its 65 mm maximum to 55 mm, yielding a 10 mm adjustment window without swapping shims or parts.
This variant includes a built-in piston magnet for AirTAC reed or electronic switches, plus a male M18x1.5 threaded piston rod end for secure external mounting. Its short riveted body drastically cuts axial mounting depth where larger profile or round-body units fail to fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X65-10SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 65 mm |
| Adjustable range | 55 – 65 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the male M18x1.5 rod extension on-site to accommodate varying carton heights without altering your pneumatic pressure settings.
When sizing this unit, evaluate your force requirements bidirectionally. Stepping down to the SDAJ40 reduces the 0.5 MPa push capacity to 628.3 N, whereas moving up to the SDAJ63 raises it to 1558.6 N. It is ideal for setups requiring frequent changeovers or trial positioning within that 55-65 mm span.
Confirm the 50 mm bore, 65 mm maximum stroke, 10 mm window, PT1/4 port, male M18x1.5 rod thread, and the integrated magnet for your assembly. Remember that a standard cylinder does not hold position if air pressure drops or the valve is centred; the piston will drift. For load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 1374.4 N and pull to 1154.5 N. The theoretical maximum push is 200 kgf at 1.0 MPa.
The external R (M16x1.5) screw mechanically shortens the forward stroke by up to 10 mm, allowing an extend range of 55-65 mm; retract remains full. The included -S magnet enables position sensing when paired with AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.