
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X85-20SB is a genuine double-acting COMPACT cylinder (Ø50mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 65 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ50X85-20SB is a compact double-acting double-rod cylinder built for tight axial spaces, featuring a short riveted body that saves mounting depth where larger profile housings fail to fit. It integrates an external R (M16x1.5) adjustment screw that lets you dial the extend end-position down by 20 mm on the machine, yielding a usable forward travel range of 65 to 85 mm without swapping shims or parts.
This specific configuration includes a built-in piston magnet (-S) for AirTAC reed or electronic solid-state switches, plus a male-threaded piston rod (-B) measuring M18x1.5 for secure external mounting. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed spans 30-500 mm/s, and the bore-fixed air port is PT1/4.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ50X85-20SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Max stroke | 85 mm |
| Adjustable range | 65 – 85 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Accommodate different box depths on the fly by shortening the forward stroke up to 20 mm, relying on the fixed NBR bumper to absorb the end shock at cycling speeds up to 500 mm/s.
When sizing this 50 mm bore actuator, evaluate both neighboring options against your payload.
This unit is ideal for operators needing frequent on-site stroke tuning during changeovers, as the M16x1.5 adjuster screw fine-tunes the extend stop from 65 to 85 mm. Note that a plain cylinder does not hold its load if air pressure drops or the valve centers; the piston will drift, as the fixed NBR bumper only decelerates near the end of travel and the adjuster acts as a mechanical stop, not a lock. For suspended or vertical loads requiring fail-safe holding, incorporate an external rod lock or pilot-operated check valve. Confirm your bore, 85 mm max stroke, 20 mm window, PT1/4 port, -S magnet, and -B male M18x1.5 rod thread before ordering.
AirtacDistr lists every SDAJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj50-adjustable-cylinder
Quick checklist
The bore-fixed air port is PT1/4.
The included -S magnet allows tracking the piston position using AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.