
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X30-20 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 10 to 30 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X30-20 is a compact double-acting double-rod cylinder featuring an external extend stop. A side-mounted R (M27x2.0) adjuster screw lets you dial the forward stroke down from 30 mm to 10 mm directly on the machine, eliminating the need for shims or part swaps during commissioning.
Built with a space-saving riveted body, this model fits where round-body or profile cylinders cannot. It uses a fixed NBR bumper at each end to absorb end-of-stroke shock rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches; you would need the -S variant for position sensing.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X30-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 30 mm |
| Adjustable range | 10 – 30 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×30 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Save axial mounting depth in cramped machinery frames while retaining the full 801 kgf maximum push capacity for heavy clamping duties.
Stepping down to an SDAJ80 yields 2513.3 N, which may be insufficient for heavy pressing or lifting tasks. Stepping up is impossible as this is the largest standard SDAJ bore, meaning any higher force requirement would require multiple cylinders or an entirely different series. This model suits applications needing exact 10-30 mm extend tuning during setup.
Remember that the adjuster screw acts purely as a mechanical stop, not a mid-stroke lock. A plain SDAJ cylinder will not hold a load if air pressure drops or the valve is centred; the piston drifts. For suspended or vertical loads, install an external rod lock or pilot-operated check valve. Confirm your requirements for the PT3/8 port, female M18x1.5 rod thread, and the lack of a magnet before ordering.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
This 100 mm bore cylinder features a PT3/8 air port.
The R (M27x2.0) screw shortens the extend stroke by up to 20 mm, allowing usable travel between 10 and 30 mm. This specific SKU has no piston magnet and cannot take a switch; adding the -S option provides a magnet for reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.