
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X45-40B is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 5 to 45 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X45-40B is a double-acting, double-rod compact cylinder featuring an external adjustable extend stop. An M27x2.0 adjuster screw lets you dial the outward stroke anywhere between 5 and 45 mm directly on the machine, avoiding part swaps.
This specific SKU includes a male-threaded M26x1.5 piston rod and lacks a piston magnet. The short riveted body drastically reduces axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, meaning the stop sets position but does not lock the load.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X45-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 45 mm |
| Adjustable range | 5 – 45 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×45 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 5 to 45 mm extend contact point for a 200 kg pressing operation without machining new spacers.
Adjust the male M26x1.5 rod extension on the fly to accommodate varying weldment thicknesses on a single line.
Fine-tune the upward travel stop during commissioning to prevent over-travel when elevating heavy fixtures.
When sizing this 100 mm bore actuator, evaluate your force needs against its neighbors. Dropping to an SDAJ80 reduces the push force to 2513.3 N at 0.5 MPa, whereas stepping up beyond 100 mm hits the top of this compact family.
Choose this model if your fixture requires precise on-site stroke tuning between 5 and 45 mm. Confirm your setup needs the PT3/8 air port and the male M26x1.5 rod end. Remember that a plain cylinder drifts when air is lost or the valve centers; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
The theoretical maximum push is 801 kgf at 1.0 MPa.
The M27x2.0 screw mechanically shortens the extend stroke by up to 40 mm, allowing you to set the outward stop anywhere from 5 to 45 mm. It does not alter the output force, and this specific SKU lacks the -S magnet required for sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.